Beamforming algorithm is widely used in many signal processing fields. At present, the typical beamforming algorithm is MVDR (Minimum Variance Distortionless Response). However, the performance of MVDR algorithm relies on the accurate covariance matrix. The MVDR algorithm declines dramatically with the inaccurate covariance matrix. To solve the problem, studying the beamforming array signal model and beamforming MVDR algorithm, we improve MVDR algorithm based on estimated diagonal loading for beamforming. MVDR optimization model based on diagonal loading compensation is established and the interval of the diagonal loading compensation value is deduced on the basis of the matrix theory. The optimal diagonal loading value in the interval is also determined through the experimental method. The experimental results show that the algorithm compared with existing algorithms is practical and effective.

Polar codes, as the coding scheme for the control channel in fifth-generation mobile communication technology (5G), have attracted widespread attention since their proposal. As a mainstream decoding algorithm for polar codes, the successive cancellation list (SCL) decoder usually improves the error correction performance by increasing the list size, but this method suffers from the problems of high decoding complexity. To address this problem, this paper proposes a layered-search bit-flipping (LS-SCLF) decoding algorithm based on SCL decoding. Firstly, a new flip-bit metric is proposed, which derives a formula to approximate the probability of an error occurring in an information bit. This formula introduces a perturbation parameter to improve the calculation accuracy. Secondly, a compromise scheme for determining the perturbation parameter is proposed. The scheme uses Monte Carlo simulation to determine an optimized parameter for the precise positioning of the first erroneous decoded bit under different decoding conditions. Finally, a layered search strategy is adopted to sequentially search the erroneous decoded bits from the low order to high order, which can correct up to multiple bits at the same time. Simulation results show that the proposed algorithm achieves improved error correction performance with a slight increase in decoding complexity compared to the generalized SCL-Flip (GSCLF) decoding algorithm. This algorithm also achieves a good balance between the error correction performance and decoding complexity.

In the third generation of the Audio Video Coding Standard (AVS3), the size of Coding Tree Units (CTUs) has been expanded to four times larger than the previous generation, and more Coding Unit (CU) partition modes have been introduced, enhancing adaptability and efficiency in video encoding. CU partition in AVS3 not only brings improvements in encoding performance but also significantly increases the computational complexity, posing substantial challenges to real-time encoding. We propose a fast algorithm for CU partition, which features adaptive tree search and pruning optimization. Firstly, it adjusts the tree search order based on neighbor CU and lookahead information. Specifically, the analysis order of sub-blocks and parent blocks is adaptively adjusted: the potential optimal partition is prioritized, the non-optimal partitions are deferred, and an optimized order of first-full-then-sub or first-sub-then-full is selected. Secondly, the pruning optimization algorithm utilizes analyzed information to skip non-optimal partitions to reduce computational complexity. Due to the adjusted tree search order and the prioritization of potential optimal partitions, more analyzed information becomes available when evaluating non-optimal partitions, thereby improving the recall and precision rates of non-optimal partitions detection, saving more time, and introducing negligible loss in coding performance. The proposed algorithm has been implemented in the open-source encoder uavs3e. Experimental results indicate that under the three encoding configurations of AI, LD B, and RA, the algorithm achieves significant time saving of 51.41%, 40.57%, and 40.57%, with BDBR increases of 0.64%, 1.61%, and 1.04%, respectively. These results outperform the state-of-the-art fast CU partition algorithms.

The decoders, which improve the error-correction performance by finding and correcting the error bits caused by channel noise, are a hotspot for polar codes. In this paper, we present a threshold based D-SCFlip (TD-SCFlip) decoder with two improvements based on the D-SCFlip decoder. First, we propose the LLR fidelity criterion to define the LLR threshold and investigate confidence probability to calculate the LLR threshold indirectly. The information bits whose LLR values are smaller than the LLR threshold will be excluded from the range of candidate bits, which reduces the complexity of constructing the flip-bits list without the loss of error-correction performance. Second, we improve the calculation method for flip-bits metric with two perturbation parameters, which locates the channel-induced error bits faster, thus improving the error-correction performance. Then, TD-SCFlip-ω decoder is also proposed, which is limited to correcting up to ω bits in each extra decoding attempt. Simulation results show that the TD-SCFlip decoding is slightly better than the D-SCFlip decoding in terms of error-correction performance and decoding complexity, while the error-correction performance of TD-SCFlip-ω decoding is comparable to that of D-SCFlip-ω decoding but with lower decoding complexity.

In the context of the high-speed development of 5G communications, high-performance decoding schemes for polar codes are a hot spot in channel coding research. Shift pruning successive cancellation list (SP-SCL) decoding aims to recover the correct path by shift pruning in the extra SCL decoding. However, the current SP-SCL decoding is inflexible in determining the shift positions. In this paper, a flexible shift pruning SCL (FSP-SCL) decoding is proposed. Firstly, the reasons for movement and the eliminated states of the correct path are analyzed in detail using the path metric range $\left(PMR\right)$, and on this basis, the validity of the method adopted in this paper for determining the shift priority of the information bits is verified. Secondly, the FSP-SCL decoding proposes two methods for determining the shift positions. One is the log-likelihood ratio (LLR) threshold method, which compares the LLR values of the eliminated paths on the shift bit with the corresponding LLR threshold to determine the shift positions. The other is the path distance method. It combines the minimum distance between the eliminated paths and the received vector with the path metrics to determine the shift positions. Both methods are more flexible and practical, as they can calculate the corresponding shift positions online based on a specific shift bit, avoiding the high complexity caused by the simulation method. Finally, this paper designs various experimental schemes to verify the decoding performance of the FSP-SCL. The experimental results show that in terms of error-correction performance, the LLR threshold-based FSP-SCL (FSPL (LLR threshold)) decoding, the path distance-based FSP-SCL (FSPL (path distance)) decoding and the existing SP-SCL decoding are roughly equal overall. In terms of decoding complexity, FSPL (LLR threshold) decoding is slightly better than FSPL (path distance) decoding, and the decoding complexity of both is lower than that of SP-SCL decoding, with the difference being more pronounced in the medium to high SNR regions.