Ultra-high-strength steels (UHSS) combined with tailor-stamping technologies are increasingly being adopted in automotive body production due to crashworthiness improvements and part weight reduction, which meet safety and energy saving demands. Recently, USIBOR®2000 (37MnB5) steel has been added to the family of UHSS. This new material allows higher performance with respect to its predecessor USIBOR®1500 (22MnB5). In this work, the two steels are compared for the manufacturing of an automotive B-Pillar by press-hardening with a tailored tool tempering approach. A Finite Element (FE) model has been developed for the numerical simulation of thermomechanical cycles of the press-hardening process. The FE-simulations have been performed with the aim of obtaining soft zones in the part, by varying the quenching time and the temperature of heated tools. The effects of these parameters on the mechanical properties of the part have been experimentally evaluated thanks to hardness and tensile tests performed on specimens subjected to the numerical thermo-mechanical cycles using the Geeble-3180 physical simulator. The results show that for both UHSS, an increase in quenching time leads to a decrease in hardness up to a threshold value, which is lower for the USIBOR®1500. Moreover, higher mechanical resistance and lower elongation at break values are derived for the USIBOR®2000 steel than for USIBOR®1500 steel.
In recent decades, the automotive industry has had a constant evolution with consequent enhancement of products quality. In industrial applications, quality may be defined as conformance to product specifications and repeatability of manufacturing process. Moreover, in the modern era of Industry 4.0, research on technological innovation has made the real-time control of manufacturing process possible. Moving from the above context, a method is proposed to perform real-time control of a deep-drawing process, using the stamping of the upper front cross member of a car chassis as industrial case study. In particular, it is proposed to calibrate the force acting on the blank holder, defining a regulation curve that considers the material yield stress and the friction coefficient as the main noise variables of the process. Firstly, deep-drawing process was modeled by using commercial Finite Element (FE) software AutoForm. By means of AutoForm Sigma tool, the stability and capability of deep-drawing process were analyzed. Numerical results were then exploited to create metamodels, by using the kriging technique, which shows the relationships between the process parameters and appropriate quality indices. Multi-objective optimization with a desirability function was carried out to identify the optimal values of input parameters for deep-drawing process. Finally, the desired regulation curve was obtained by maximizing total desirability. The resulting regulation curve can be exploited as a useful tool for real-time control of the force acting on the blank holder.
In the deep drawing process, the scatter of the friction coefficient between blank and tool interfaces as well as of the material properties between blank positions in the coil or between different coils significantly influences the part quality. These uncontrollable fluctuations increase the risk of waste. To avoid this problem, currently, the new era of Industry 4.0 aims at developing control algorithms able to in-line adjust process parameters and always meet the part quality requirements. Starting from this context, in this study a method for process control during the punch stroke is proposed. It assumes the blank draw-in in specific points as the control variable, while the blank holder force is adopted as an in-line adjustable process parameter. The approach was implemented for the deep drawing of a T-shaped component, using a blank in DC05 steel with a thickness of 0.75 mm. The results show that the measurement of blank draw-in is a representative index of the component quality, which in this study is evaluated in terms of formability (thinning) and cosmetic (surface deflections) defects. Once the optimal condition and the corresponding blank draw-in were identified, the feedback control algorithm was able to increase or reduce the blank holder force according to whether the recorded draw-in was higher or lower than the optimal one.
The deformation behavior and the constitutive description of materials are important in the design and numerical simulation of manufacturing processes. In this work, the rheological behavior of two quenchable boron steels was derived in the range of interest for the Press Hardening (PH) process. For this study, the following steps were performed: (i) Design of the specimen geometry adopted during the hot tensile tests in the Gleeble®3180 physical simulator. (ii) Performance of hot tensile tests at temperatures between 750 and 850 °C and strain rates of 0.01–1 s−1. (iii) The description of the material constitutive model by means of the Arrhenius-type equation and the comparison between the experimental and predicted data. Firstly, the method was validated on USIBOR®1500 boron steel by means of a comparison with existing literature data, and good agreement with other scientific works was found. Finally, this method was also adopted on USIBOR®2000, a steel that belongs to the new generation of Ultra-High-Strength Steels (UHSS). A comparison between the rheological behavior of these two steels was carried out. The results show that USIBOR®2000 steel exhibits greater strength compared to USIBOR®1500 steel. The Arrhenius constitutive model well predicts the flow behavior of both steels.
14 October 2020 in The International Journal of Advanced Manufacturing Technology
The study focuses on the analysis of the softening effects of the work-hardened aluminum alloy sheets EN AW 5754 H32 1.5 mm thick, through the physical simulation of thermal cycles induced in the material by laser heat treatments (LHTs). A numerical-experimental approach was implemented to define the laser thermal cycles and to subsequently reproduce them on the GleebleTM 3180 physical simulator. The obtained softening was measured by microhardness and metallographic analysis tests. For the definition of laser thermal cycles, preliminary tests with a 2.5 kW CO2 laser source have been realized, and a three-dimensional transient finite element thermal models were developed and calibrated with the experimental results. The investigated laser heat treatment parameters explored thermal cycles with different shape, interaction time, and peak temperature. Physical simulation tests were performed using laser thermal cycles that showed the maximum softening of the aluminum alloy. A three-dimensional transient finite element thermoelectric model was developed to design the shape of the Gleeble specimens, which satisfy the heating and cooling rate required by laser thermal cycles. Results obtained show that it is possible to physically simulate the investigated laser thermal cycles, reducing the cross section of the shaped part of the specimen. Softening effects depend on the thermal cycle shape. Greater softening is observed by increasing the interaction time and the peak temperature, but beyond a peak temperature threshold value, negligible effects are detected.
During the forming process, variations in noise parameters can negatively impact product quality. To prevent waste from these fluctuations, this study suggests a method for the in-line optimisation of the deep drawing process. The noise parameter considered is the friction coefficient, assuming the variability in lubrication conditions at the blank–tool interface. The proposed approach estimates the noise factor variability during the process by tracking the draw-in of the blank at critical points. Using this estimation, the optimal blank holder force (BHF) is calculated and then adjusted in-line to modify blank sliding and prevent critical issues on the component. For this purpose, a Finite Element (FE) model of a deep drawing case study was developed, and numerical simulation results were used to construct surrogate models while estimating both the friction coefficient and optimal BHF. The FE model’s predictive capability was verified through preliminary experimental tests, and the control logic was numerically validated. Results show the effectiveness of this control type. By adjusting the BHF just once, a defect-free component is achieved. This method overcomes the limitations of feedback controls, which often need multiple adjustment steps. The time required to estimate the friction coefficient and the maximum time available for adjusting the BHF without causing defects was identified.