Necmiye Funda Ak Azem

Dr. Necmiye Funda Ak Azem

orcid

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2014 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
Alina Vladescu (Dragomir)Alina Vladescu (Dragomir)
Alina Vladescu (Dragomir)
IBI. Birlik
I. Birlik
VBViorel Braic
Viorel Braic
MTMustafa Toparli
Mustafa Toparli
ECE. Celik
E. Celik
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem

1 November 2016 in Materials Science and Engineering: C
Verified
Journal Article
Closed access
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem
TDTulay KOÇ DELİCE
Tulay KOÇ DELİCE
GUGuler Ungan
Guler Ungan
ACAhmet Cakir
Ahmet Cakir

3 November 2017 in Coatings
Verified
Journal Article
Open access
PDF file
TMThomas Monsees
Thomas Monsees
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem
Cosmin Mihai CotrutCosmin Mihai Cotrut
Cosmin Mihai Cotrut
Mariana BraicMariana Braic
Mariana Braic
RARadwan Abdulgader
Radwan Abdulgader
Alina Vladescu (Dragomir)Alina Vladescu (Dragomir)
Alina Vladescu (Dragomir)
This study aims to analyze hydroxyapatite (HAP) coatings enriched with Mg and Ti prepared by a magnetron sputtering technique on Ti6Al4V substrate. For preparation of the coatings, three magnetron targets (HAP, MgO and TiO2) were simultaneously co-worked. The concentration of Mg added was varied by modifying the power applied to the MgO target. In all coatings, the Ti concentration was maintained constant by keeping the same cathode power fed during the whole deposition. The influence of different Mg dopant contents on the formation of phase, microstructure and morphology of the obtained Ti-doped HAP coatings were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Moreover, the effects of Mg addition upon corrosion, mechanical and biological properties were also investigated. Mg- and Ti-doped HAP coating obtained at low radio-frequency (RF) power fed to the MgO target provided material with high corrosion resistance compared to other coatings and bare alloy. A slight decrease in hardness of the coatings was found after the Mg addition, from 8.8 to 5.7 GPa. Also, the values of elastic modulus were decreased from 87 to 53 GPa, this being an advantage for biomedical applications. The coatings with low Mg concentration proved to have good deformation to yielding and higher plastic properties. Biological test results showed that the novel surfaces exhibited excellent properties for the adhesion and growth of bone cells. Moreover, early adherent vital cell numbers were significantly higher on both coatings compared to Ti6Al4V, suggesting that Mg ions may accelerate initial osteoblast adhesion and proliferation.

17 April 2009 in Journal of Sol-Gel Science and Technology
Verified
Journal Article
Closed access
PDF file
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem
ACA. Cakir
A. Cakir

1 April 2024 in Materials Research Express
Verified
Journal Article
Open access
TDTulay Koc Delice
Tulay Koc Delice
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem
KOKazim Ozdemir
Kazim Ozdemir
SASenol Alpat
Senol Alpat
Metal oxide structures are being utilized in an increasing variety of applications. This study used cyclic and differential pulse voltammetry techniques to investigate the possible utilization of copper oxide (CuO) nanoparticles modified carbon paste electrode (CPE) for the redox reactions of salbutamol (SAL). The electrochemical performance of the SAL analyte in a complex matrix environment in Ventolin was evaluated in order to assess the appropriateness of the proposed sensor in a real sample environment. CuO nanoparticles were produced via a straightforward, cost-effective and efficient sol–gel method, and characterization studies of synthesized CuO nanoparticles were performed by scanning electron microscopy, x-ray Diffraction (XRD), and x-ray photoelectron spectroscopy. The synthesized CuO nanoparticles had a spherical shape and particle size was found to be 74 nm. The crystal size of the CuO particles was calculated to be 21.79 nm using the Debye–Scherrer equation. Under optimal conditions, differential pulse voltammetry demonstrated a linear response in the 50 nM to 100 μM range, with a salbutamol detection limit of 50 nM (S/N = 3). The SAL concentration (R 2 = 0.9971) was found to have a good correlation coefficient. The reproducibility of the biosensor was investigated and evaluated with a relative standard deviation of 3% (n = 8). The storage stability of CuO modified CPE for two weeks was evaluated based on the response of DP current measured at intervals every two days. According to the measurement results, the modified electrode exhibited good stability and reproducibility while maintaining 80% of its stability. It is also a rapid and dependable sensor candidate with a measurement time of approximately 20 s. The developed electrode has been utilized successfully to determine doping material with improved performance.

28 February 2026 in Nanomaterials
Verified
Journal Article
Open access
PDF file
FSFATİH SARGIN
FATİH SARGIN
NANecmiye Funda Ak Azem
Necmiye Funda Ak Azem
CeO2 particles were synthesized via a hydrothermal method to investigate the influence of precursor molarity and reaction time on their structural, optical, and adsorption characteristics. Ce(NO3)3·6H2O served as the cerium source, while PVP and Triton X-100 acted as surfactants to regulate nucleation and particle growth. XRD and Raman analyses confirmed the formation of single-phase cubic fluorite CeO2, whereas FTIR spectra verified the presence of Ce–O bonding. SEM observations revealed that a decreasing precursor molarity led to smaller and more uniform particles, while prolonged reaction times enhanced crystallinity. UV–Vis DRS and XPS analyses indicated that both the band gap (3.06–3.12 eV) and the Ce3+/Ce4+ ratio were governed by oxygen vacancies, demonstrating defect-mediated redox behavior. Adsorption studies using methyl orange (MO) dye followed pseudo-second-order kinetics (R2 > 0.99), indicating chemisorption as the dominant mechanism. The CP1-8 sample exhibited the highest dye removal efficiency (87%) under acidic conditions (pH < pHPZC). These findings demonstrate that controlled hydrothermal synthesis enables precise tuning of CeO2 morphology, defect density, and surface chemistry, yielding efficient adsorbent materials for environmental remediation applications.