ABDELLAH DOUADI

Dr. ABDELLAH DOUADI

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 July 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
RBRiad Babba
Riad Babba
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
MBMourad Boutlikht
Mourad Boutlikht
RHRedha Hammouche
Redha Hammouche
Laura MorettiLaura Moretti
Laura Moretti
Premature debonding between carbon fiber-reinforced polymer (CFRP) and concrete is a critical issue in structural reinforcement applications, often leading to a significant reduction in the load-carrying capacity of the system. This failure mode is typically initiated by inadequate adhesion at the interface, compromising the effectiveness of CFRP in enhancing the structural performance of concrete elements. To address these issues, this study explores the impact of silica sand on the mechanical and adhesion properties of epoxy resin composites. Initially, this paper investigates the physical and mechanical properties of epoxy resin composites by varying the ratios of silica sand from 0% to 15% by volume. Subsequently, it examines the effectiveness of these composites as sealing materials to enhance the bond strength between CFRP and concrete. Incorporating a 10% silica content improves the mechanical properties of the epoxy resin, with the tensile strength increasing from 29.47 MPa to 35.52 MPa and an elastic modulus from 4.38 GPa to 5.83 GPa. Furthermore, silica sand enhances the adhesion strength between CFRP and concrete, as confirmed by the increase in the pull-out force from 14.21 kN to 18.79 kN. Silica particles improve surface roughness and interlocking, contributing to a better load distribution and stress transfer at the interface. Therefore, silica-filled epoxy resin is an efficient material for CFRP–concrete bonding applications.

25 October 2023 in Materials
Verified
Journal Article
Open access
PDF file
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
MBMourad Boutlikht
Mourad Boutlikht
STSeifeddine TABCHOUCHE
Seifeddine TABCHOUCHE
CBCherif Belebchouche
Cherif Belebchouche
Laura MorettiLaura Moretti
Laura Moretti
The environmental impacts of cement manufacturing are becoming a real-time issue that requires attention. This paper investigates the mechanical and physical properties of mortars with finely ground sand as a substitute for cement. The experimental program consisted of three silica sands with a Blaine Specific Surface (BSS) area of 459 m2/kg, 497 m2/kg, and 543 m2/kg and four substitution ratios of 10%, 20%, 30%, and 40%. A total of 12 mixtures have been prepared and tested for comparison to the reference mortar. The pozzolanic effect of the sand was evaluated using thermogravimetric analysis (TGA). The results revealed that the fineness variation from 459 m2/kg to 543 m2/kg resulted in an increase of 20% and 30% in water absorption and compressive strength, respectively. However, increasing the substitution ratio from 10% to 40% led to a 40% decrease in mechanical strength and a 25% increase in water absorption. The statistical analysis of the results demonstrated that both factors under study influenced compressive strength and water absorption. The ANalysis of VAriance (ANOVA) confirmed that the proposed regression equations predict the experimental results. Further studies will investigate both the technical and environmental performances of cement mortars with finely ground silica sand.

12 March 2025 in Journal of Cleaner Production
Verified
Journal Article
Closed access
RHRedha Hammouche
Redha Hammouche
CBCherif Belebchouche
Cherif Belebchouche
AHAbdelkader Hammoudi
Abdelkader Hammoudi
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
Sławomir CzarneckiSławomir Czarnecki
Sławomir Czarnecki

24 March 2025 in Buildings
Verified
Journal Article
Open access
PDF file
MBMourad Boutlikht
Mourad Boutlikht
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
NKNour El Houda KHITAS
Nour El Houda KHITAS
AMAbderraouf MESSAI
Abderraouf MESSAI
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
TTTaher A. Tawfik
Taher A. Tawfik
The disposal and recycling of industrial by-products such as marble and limestone powders pose pressing environmental challenges due to the substantial amounts of waste generated annually by marble processing plants and limestone quarries. The integration of these by-products into concrete production is justified by their widespread availability and the potential to alleviate the environmental burden. This study used a statistical mixture design approach to systematically assess the effects of limestone and marble powders, with varying fineness levels, as partial cement replacements (up to 17%) on the rheological and mechanical properties of self-compacting concrete (SCC). The experimental findings revealed that the density of the SCC mixtures ranged from 2475 to 2487 kg/m3. Mixtures incorporating limestone powder exhibited superior flowability, achieving a slump flow of up to 69 cm, an 8% improvement compared to those containing marble powder. However, marble powder with a specific surface area of 330 m2/kg demonstrated significant improvements in compressive and tensile strengths, with increases of 18%. Statistical analysis using analysis of variance (ANOVA) validated the reliability of the predictive models developed, which demonstrated coefficients of determination (R2) that exceeded 0.94 and p-values below 0.05. These models enable precise predictions of critical performance metrics, including density, slump flow, box flow, compressive strength, and tensile strength, thus reducing the need for extensive experimental procedures.

18 February 2025 in Buildings
Verified
Journal Article
Open access
PDF file
ZLZakarya Laouidji
Zakarya Laouidji
MBMourad Boutlikht
Mourad Boutlikht
ABDELLAH DOUADIABDELLAH DOUADI
ABDELLAH DOUADI
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
EAElhoussine Atiki
Elhoussine Atiki
Sławomir CzarneckiSławomir Czarnecki
Sławomir Czarnecki
The clay brick industry is facing significant challenges related to improving its physico-mechanical properties and durability performance of sustainable products. The current study aimed to investigate the effect of stabilizers (lime and cement) on the clay brick properties of three soils. The investigated soils were taken from different regions of Algeria. A series of laboratory experiments were carried out to examine the effect of lime and cement addition with different ratios of 2%, 4%, 6%, 8%, and 10%, on the mechanical properties. The assessment was based on compressive strength, flexural strength, total and capillary water absorption tests. The test results showed that the lime addition to soils A and B led to a significant increase in compressive strength (CS) by 47% and 101%, respectively. The highest values obtained were for the 8% ratio. The obtained gain in compressive strength soil C reached its maximum CS at 6% ratio, and the obtained gain was 44%. However, for cement addition, the highest CS values were obtained at the 10% ratio for all studied soils. The observed gains in compressive strength for soils A, B, and C were 24%, 15%, and 33%, respectively. Flexural strength (FS) followed a similar trend, with lime addition improving (FS) by up to 400% for soil A at an 8% ratio. Cement addition also enhanced (FS), with the highest improvement of 103%, which was observed for soil A at a 10% ratio. It was also observed that lime addition significantly decreased the total absorption by up to 36% at an 8% ratio for soils A and B, and at 6% for soil C. In contrast, the total absorption decreased uniformly with the cement addition up to the 10% ratio. The lowest absorption observed at a 10% ratio was 11.95%. Lime addition also decreased the capillary absorption of clay bricks, and the lowest value was observed at an 8% ratio for both soils (A and B) and 6% for soil C. The CA values decreased by approximately 24% for soils A and B and 14% for soil C. In the case of cement addition, it was noted that the capillary absorption had the same pattern as the total absorption. The percentage decreases in CA were 41%, 40%, and 38% for soils A, B, and C, respectively. These results indicate that the enhancement of clay brick was observed for lime addition ranging from 2% to 8%. Therefore, good mechanical strengths were obtained at a 10% cement ratio.

5 June 2025 in Materials
Verified
Journal Article
Open access
PDF file
BBBesma Belaidi
Besma Belaidi
AMAbderraouf MESSAI
Abderraouf MESSAI
CBCherif Belebchouche
Cherif Belebchouche
MBMourad Boutlikht
Mourad Boutlikht
Kamel HEBBACHEKamel HEBBACHE
Kamel HEBBACHE
Laura MorettiLaura Moretti
Laura Moretti
The cement industry is a major contributor to global CO2 emissions, driving the research for sustainable alternatives. Olive biomass ash (OBA), a byproduct from burning all types of biomass from the olive tree, has emerged as a potential supplementary cementitious material (SCM). This study investigates the effects of incorporating olive pomace ash (OPA) as a partial cement substitute (0% to 50% by weight) on mortar properties over extended curing periods. Workability, compressive and flexural strengths, water absorption, and freeze–thaw resistance were evaluated. Up to 20% OPA replacement improved workability while maintaining acceptable strength and durability. Beyond this level, mechanical properties and frost resistance decreased significantly. Correlation analyses revealed strong relationships between flow time and wet bulk density (R2 = 0.93), an exponential relationship between 28-day compressive strength and water absorption (R2 = 0.87), and linear correlations between pre- and post-freeze–thaw mechanical properties (R2 ≥ 0.99 for both compressive and flexural strengths). The results demonstrate that optimal OPA incorporation enhances mortar performance without compromising structural integrity and provides a viable strategy for valorizing agricultural waste.