Božica Bojović

Prof. Dr. Božica Bojović

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 October 2023 in Polymers
Verified
Journal Article
Open access
PDF file
Zorana GolubovićZorana Golubović
Zorana Golubović
IDIvan Danilov
Ivan Danilov
Božica BojovićBožica Bojović
Božica Bojović
LPLjubiša S Petrov
Ljubiša S Petrov
aleksandar sedmakaleksandar sedmak
aleksandar sedmak
Nenad MitrovicNenad Mitrovic
Nenad Mitrovic
Additive manufacturing technologies have developed rapidly in recent decades, pushing the limits of known manufacturing processes. The need to study the properties of the different materials used for these processes comprehensively and in detail has become a primary goal in order to get the best out of the manufacturing itself. The widely used thermoplastic polymer material acrylonitrile butadiene styrene (ABS) was selected in the form of both filaments and ABS-like resins to investigate and compare the mechanical properties through a series of different tests. ABS-like resin material is commercially available, but it is not a sufficiently mechanically studied form of the material, which leads to the rather limited literature. Considering that ABS resin is a declared material that behaves like the ABS filament but in a different form, the objective of this study was to compare these two commercially available materials printed with three different 3D printers, namely Fused Deposition Modelling (FDM), Stereolithography (SLA) and Digital Light Processing (DLP). A total of 45 test specimens with geometries and test protocols conforming to the relevant standards were subjected to a series of tensile, three-point bending and compression tests to determine their mechanical properties. Characterization also included evaluation of morphology with 2D and 3D microscopy, dimensional accuracy of 3D scans, and Shore A hardness of each material and 3D printing process. Tensile testing results have shown that FDM toughness is 40% of the value for DLP. FDM elongation at break is 37% of DLP, while ultimate tensile stress for SLA is 27% higher than FDM value. Elastic modulus for FDM and SLA coincide. Flexure testing results indicate that value of DLP flexural modulus is 54% of the FDM value. SLA strain value is 59% of FDM, and DLP ultimate flexure stress is 77% of the value for FDM. Compression test results imply that FDM specimens absorb at least twice as much energy as vat polymerized specimens. Strain at break for SLA is 72% and strain at ultimate stress is 60% of FDM values. FDM yield stress is 32% higher than DLP value. SLA ultimate compressive stress is half of FDM, while value for DLP compressive modulus is 69% of the FDM value. The results obtained are beneficial and give a more comprehensive picture of the behavior of the ABS polymers used in different forms and different AM processes.

10 April 2024 in Polymers
Verified
Journal Article
Open access
PDF file
Zorana GolubovićZorana Golubović
Zorana Golubović
Božica BojovićBožica Bojović
Božica Bojović
SKSnezana Kirin
Snezana Kirin
AMAleksa Ljubomir Milovanovic
Aleksa Ljubomir Milovanovic
LPLjubiša S Petrov
Ljubiša S Petrov
ISIvana Sofrenić
Ivana Sofrenić
Additive manufacturing, with its fast development and application of polymeric materials, led to the wide utilization of polylactic acid (PLA) materials. As a biodegradable and biocompatible aliphatic polyester, produced from renewable sources, PLA is widely used in different sectors, from industry to medicine and science. The aim of this research is to determine the differences between two forms of the PLA material, i.e., fused deposition modeling (FDM) printed filament and digital light processing (DLP) printed resin, followed by aging due to environmental and hygiene maintenance conditions for a period of two months. Specimens underwent 3D scanning, tensile testing, and Fourier transform infrared (FTIR) spectrometry to obtain insights into the material changes that occurred. Two-way Analysis of Variance (ANOVA) statistical analysis was subsequently carried out to determine the statistical significance of the determined changes. Significant impairment can be observed in the dimensional accuracies between both materials, whether they are non-aged or aged. The mechanical properties fluctuated for aged FDM specimens: 15% for ultimate tensile stress, 15% for elongation at yield, and 12% for elastic modulus. Regarding the DLP aged specimens, the UTS decreased by 61%, elongation at yield by around 61%, and elastic modulus by 62%. According to the FTIR spectral analysis, the PLA materials degraded, especially in the case of resin specimens. Aging also showed a significant influence on the elastic modulus, ultimate tensile stress, elongation at yield, elongation at break, and toughness of both materials, which was statistically shown by means of a two-way ANOVA test. The data collected in this research give a better understanding of the underlying aging mechanism of PLA materials.

26 April 2025 in Polymers
Verified
Journal Article
Open access
PDF file
Zorana GolubovićZorana Golubović
Zorana Golubović
Jovan D. Tanaskovic, Dipl. -Ing. Mech.Jovan D. Tanaskovic, Dipl. -Ing. Mech.
Jovan D. Tanaskovic, Dipl. -Ing. Mech.
AMAleksa Ljubomir Milovanovic
Aleksa Ljubomir Milovanovic
Božica BojovićBožica Bojović
Božica Bojović
Additive manufacturing (AM), especially vat photopolymerization processes such as digital light processing (DLP), enables the production of highly detailed and complex geometries with precise material structure control. In this study, the influence of internal structure on the mechanical properties of PLA resin specimens produced using a DLP 3D printer is investigated. Two designs were analyzed: a fully solid structure and a shell with a Voronoi pattern. Tensile and bending tests revealed that solid specimens exhibited higher strength, while Voronoi structures performed better under bending loading despite lower load-bearing capacity due to their porosity ratio. The developed numerical model, analyzed through different numerical simulations using the Ansys 2025R01 Software package and validated by experimental results, showed a strong correlation between experimental and numerical results that confirmed the reliability of the developed models for preliminary design verification. These models hold significant potential for the design of mechanical and biomedical components, including orthopedic immobilization devices. Microscopic analysis revealed brittle fracture in solid specimens with striations and bubble-shaped irregularities, while Voronoi specimens exhibited fragmented surfaces with clean, brittle failure along structural voids. Based on the results obtained, this research demonstrates how additive manufacturing enables the optimization of mechanical properties and material efficiency through precise control of internal structures. In the future, validated numerical models can be used to check the preliminary designs of different components, which will significantly reduce development costs.

1 January 2025 in FME Transactions
Verified
Journal Article
Open access
PDF file
IDIvan Danilov
Ivan Danilov
Zorana GolubovićZorana Golubović
Zorana Golubović
AMAleksa Milovanović
Aleksa Milovanović
Boban AndjelkovicBoban Andjelkovic
Boban Andjelkovic
MŽMilovan Živković
Milovan Živković
Božica BojovićBožica Bojović
Božica Bojović
This study investigates the environmental aging effects on 3D-printed Acrylonitrile Butadiene Styrene (ABS) produced using Fused Deposition Modeling (FDM) and Digital Light Processing (DLP) techniques. The materials in filament (FDM) and resin (DLP) forms were exposed to UV light, humidity, and temperature fluctuations over two months. Mechanical testing via three-point bending and Fourier Transform Infrared Spectroscopy (FTIR) were employed to assess the impact of these environmental factors. Results showed notable mechanical strength and structural stability differences between the FDM-printed filament and DLP-printed resin ABS under aging conditions. The filament-based ABS exhibited superior mechanical properties, retaining its strength over time, while the resin-based ABS degraded significantly shortly after printing. Despite exposure to ambient environmental conditions, the chemical composition of both materials remained stable throughout the research period.

29 February 2024
Verified
Book Chapter
Closed access
PDF file
Božica BojovićBožica Bojović
Božica Bojović
ZGZorana Golubović
Zorana Golubović
LPLjubiša Petrov
Ljubiša Petrov
AMAleksa Milovanović
Aleksa Milovanović
ASAleksandar Sedmak
Aleksandar Sedmak
MMMiloš Milošević
Miloš Milošević

1 January 2020 in FME Transactions
Verified
Journal Article
Open access
PDF file
APAleksandar Popović
Aleksandar Popović
Božica BojovićBožica Bojović
Božica Bojović
MSMarcel Suter
Marcel Suter
DNDavid Niederer
David Niederer
The paper presents an analysis of reluctance actuator for speckle reducing in laser based projectors, head-up displays, metrology and 3D scanning units to improve the quality of the generated images by a moving diffuser. Design concepts for one-dimensional laser speckle reducer actuator are analyzed through different designs structures. There are two resonant structures with three spring lengths, and two actuation structures with single tooth and double teeth. Reluctance actuator is evaluated in details, taking into account simple design and functional requirements of the laser speckle reducer (generated force and maximum displacement). The resonate frequency and influence of geometrical parameters are determined with the use of COMSOL Multiphysics. The forces developed through the actuating structures are obtained from the simulated material magnetic flux distribution, saturation. Evaluation suggests the next steps in the actuating structure optimization from which better performance of the device could be obtained.