This research applied the Non-Destructive Testing (NDT) method of the emission gas produced by methanil yellow waste, carbon dioxide (CO2) and hydrogen (H2) gases with TiO2 as catalyst material to detect the concentration of methanil yellow waste using artificial neural network based on microcontroller. This device consists of Arduino UNO, LCD 16x2 I2C, MQ-8 H2 gas sensor, MQ-135 CO2 gas sensor, BH1750 light sensor and DHT11 temperature sensor. The concentration of waste is 5-30 mg/L with variations range 5 mg/L. Meanwhile, the neural network architecture was created using the Matlab R2018a application. The architecture that owned 25 neurons was chosen due to its performance value with an error of $3.98\ \times \ {10}^{ - 25}$ and epoch 165. The result of Artificial Neuron Network (ANN) training on Matlab of 4-25-1 architecture contains error value of 0.024%. The weight and bias values in the training process are programming ANN to Arduino. The testing has an error value of 6.028% and RMSE 0.552. Based on the error values, it shows that the training is reaching closely to the actual value, it can be concluded that the device can work properly and practical to use because it does not take a long to observe.
This research conducted a datasheet-based calibration study using the MQ-135 sensor and MQ-8 sensor to measure carbon dioxide and hydrogen. The process of digitizing datasheet graphs into numbers that have a relationship between electrical quantities and physical quantities (R versus ppm) is carried out using webPlotDigitizer software. Based on the calculation results, a trendline of the power equation model has been obtained for the MQ-135 gas sensor and MQ-8 gas sensor respectively from the comparison of the x-axis (ADC) and y-axis (PPM), namely with a value of , and with a value of . Based on the value or coefficient of determination for each sensor, it shows that the value is close to 1, so this shows that the trendline of the power equation model used matches the sensor datasheet. The equations and will then be entered into the Arduino IDE program as calibration values for the MQ-135 sensor and MQ-8 sensor to obtain measurement values that are in accordance with the standardized datasheet. To improve accuracy, calibration was also performed using a reference instrument, a Carbon Dioxide Detector for and a C-200 Pen-Type Water Quality Meter for , with average errors of 1.29488% and 29.81805%, respectively. The low error value for indicates good compliance, while the high error for is due to limitations of the reference instrument. This method can be an alternative when resources are limited, provided that the limitations of the instrument are still considered.
10 June 2023 in International Journal of Scientific Research in Science and Technology
An analysis has been carried out for the Spring Damper System using the Python programming language on Google Colab. The first stage that is carried out before the simulation is to determine the differential equation based on Newton's II law equation. The Python programming language was chosen because only needs to run in a browser, users can monitor the training process (or even coding) via a smartphone browser if the smartphone is connected to the same Google Drive. The simulation is carried out by varying the mass value from 5kg - 50kg with a mass increase range of 5kg. This is done to determine the effect of mass on changes in position and velocity/speed. Based on the simulation results, the greater the mass value given will affect the amplitude value, the position graph will increase while the velocity graph will decrease, and the time needed for both amplitudes to stabilize will increase.
30 June 2024 in The Indonesian Journal of Computer Science
Studies have been carried out related to the application of bioinformatics which includes genomics, proteomics and metabolomics in everyday life, such as in the fields of health, agriculture, environment, renewable energy and food. Evaluation of the quality of the papers used is based on papers available in each journal on platforms such as Scopus, Google Scholar, as well as articles published by Elsivier, Springer Nature, etc. The stages carried out in this research include journal data collection, journal renewal, journal grouping, and journal comparison. Based on this application, it has been proven that bioinformatics has achieved success in understanding various biological aspects. Thus, it is hoped that this research can provide deeper insight regarding the use of bioinformatics in various other fields.