The aim of this study was to investigate the effects of different working parameters on the cleaning efficiency of a cleaning device during the separation and cleaning process in a flax joint harvesting machine. To achieve this objective, CFD–DEM joint simulation technology was used to construct a CFD model of the cleaning device and a DEM model of the discharged flax material; the simulation results show the flax cleaning process. The Box–Behnken experimental design method was used to establish a mathematical model between the vibrating sieve frequency, vibrating sieve amplitude, fan wind speed, seed impurity rate, and cleaning loss rate to find the optimum combination of cleaning equipment parameters and to conduct a field verification test. The simulation test results show that, when the vibrating sieve frequency is 6 Hz, the vibrating sieve amplitude is 14.42 mm, the fan wind speed is 5.96 m/s, and the machine cleaning effect is the best; the simulation test was measured following a seed impurity rate of 2.97% and cleaning loss rate of 2.17%. The field test verification results show that, after optimizing the working parameters of the cleaning device, the cleaning loss rate is 3.58% and the impurity rate of the grain combine harvester is 3.16%, thus meeting the national and industry requirements. The test results and simulation results are highly consistent with the model, thereby verifying the reliability of the model. The results of the study provide a reference for the design and performance optimization of the flax combine cleaner.

To conduct an in-depth investigation of the impact of various operating parameters on mulching device wear during the operation of full-film dual-row ridging and mulching machine mulching, this paper employed EDEM software to create a 3D discrete element model of how a mulching device interacts with the soil on the seed bed and simulated the dynamic process of the interaction between the mulching device and the soil during the mulching operation. We analyzed the cladding wear process between the cladding device and the cladding sand particles, and two areas of impact wear on the overburden conveyor housing and areas of wear on the chute deflector scratches were detected. A three-factor, three-level Box–Behnken experimental design approach was used, with mathematical modeling of the relationship between the scraper conveyor lifting line speed, seed bed cover, scraper spacing, and wear of the cover device, finding the optimal combination of operating parameters for mulching devices. The results of the simulation test indicated that the mulching device experienced a minimum wear of 0.958 × 10⁻³ mm at a lifting line speed of 0.7 m·s⁻¹ for the scraper conveyor, a mulching volume of 2.55 kg·s⁻¹ for the seed bed, and a scraper spacing of 98 mm. The results of the field trial validation showed that, in a comparison between simulated wear parts and a mulching operation prototype of the same two wear parts, the established discrete element model appeared reasonable concerning the structural parameters, with a feasible abrasion mechanism process of sand particles on the soil-covering devices, demonstrating the model’s reliability and validity. It can serve as a guide for optimizing the design of mechanized full-film dual-furrow seed bed mulching operation.

The process of hole seeding on the mulch during full-film double-row furrow corn planting faces issues such as poor seed discharge and seed blockage. To address these challenges, a pendulum-lever-type hole-forming mechanism is designed, along with an adjustment device. By analyzing the working principles of the pendulum-lever-type hole seeder and the adjustment device, the structural parameters of the device are determined. Through theoretical analysis and simulation experiments, three-dimensional models of seeds and hole seeders are constructed. Based on MBD-DEM cosimulation, the trajectory of seed movement and the seeding process of the hole seeder are analyzed to elucidate the effects of the hole-former opening and the number of pendulum bearings on seeding quality. To improve the operational performance of the hole seeder, experiments are conducted using the hole seeder’s rotating disc speed, lever angle of the hole-former, and the number of pendulum bearings as experimental factors, with the qualification index, miss-seeding index, and reseeding index as experimental indicators. A three-factor, three-level Box–Behnken central composite experiment is performed to obtain mathematical models of the relationships between the experimental factors and indicators. Using Design-Expert 12 software, the regression models are optimized for multiple objectives to obtain the optimal parameter combination: a seeder disc speed of 49 r/min (corresponding to a forward speed of 5.76 km/h), a lever angle of 131°, and four pendulum bearings. Under this optimal parameter combination, the qualification index is 91.70%, the miss-seeding index is 4.57%, and the reseeding index is 3.73%. Experimental validation of the seeding performance of the hole seeder under the optimal parameter combination is conducted. Bench tests show that the qualification index, miss-seeding index, and reseeding index are 90.53%, 5.60%, and 3.87%, respectively. Field tests demonstrate a qualification index of 89.13%, a miss-seeding index of 5.46%, and a reseeding index of 6.41%. The actual results are consistent with the optimized values, providing valuable insights for the design and performance optimization of hole seeders.

Water is an important factor limiting the development of arid rain-fed agriculture. Film mulching is an effective way to ensure yield in arid areas. However, whether biodegradable film can be used instead of polyethylene film for agricultural production in arid areas is a matter of contention. In this study, AquaCrop model simulation and field experiment were used to analyze the production effect of corn whole film double ridge furrow sowing technology covering polyethylene film (PM) and biodegradable film (BM) in Dingxi City from 2016 to 2020. The results showed that the AquaCrop simulation data have a high fitting with the field test data, and the model was suitable for simulating dry farming in Dingxi City. The best sowing time in Dingxi City is to select the average temperature to be stable at about 15 °C (around 15 April to 25 April each year), and the yield is the highest after sowing during this period. Although BM can achieve environmental protection and energy saving, it is weaker than PM in water storage and soil evaporation inhibition in arid areas. The average yield, aboveground biomass, water productivity, and harvest index of PM were 63.95%, 18.57%, 76.35%, and 38.22% higher than those of BM, respectively. In drought years, BM water stress on leaf expansion, induced stomatal closure, and premature senescence were 61%, 17%, and 9.5% higher than PM, respectively, and the stress time was 28.5 d, 5 d, and 26 d, respectively. The maximum canopy coverage and effective root zone water content were 24.5% and 30.49% lower, respectively. In the wet year, water stress under BM only had a certain effect on the leaf expansion of crops but had no effect on the induction of stomatal closure and premature senescence. The maximum canopy coverage and effective root zone water content were 13.56% and 31.35% lower, respectively. The above studies show that BM has a certain ability to store water and preserve moisture, but the parameters of PM are better than BM. Especially in dry years, the crop production efficiency of PM is more significant. It can be seen that in rain-fed agricultural areas with rainfall less than 500 mm, biodegradable film can not replace polyethylene film.

The arid area of Northwest China belongs to the rain-fed agricultural area of the Loess Plateau, and water resources have become one of the important factors limiting agricultural development in this area. This study employed the AquaCrop model to predict the yield advantages and environmental adaptability of maize in Dingxi City from 2016 to 2020 under two cultivation practices: ridge tillage (100% film coverage with double ridge-furrow planting) and flat planting (81.8% film coverage with wide-film planting). The numerical simulation of the tillage and fertilization process of the double-ridge seedbed was carried out by EDEM, and the key components were tested by the Box–Behnken center combination test design principle to obtain the optimal parameter combination. The results showed that ridge planting was more suitable for agricultural planting in rain-fed arid areas in Northwest China. The simulation analysis of ridging and fertilization showed that the forward speed of the combined machine was 0.50 m/s, the rotation speed of the trough wheel of the fertilizer discharger was 39 rmp, and the rotary tillage depth was 150 mm. The qualified rate of seedbed tillage was 93.6%, and the qualified rate of fertilization was 92.1%. The research shows that the whole-film double ridge-furrow sowing technology of maize is more suitable for the rain-fed agricultural area in the arid area of Northwest China. The simulation results of the ridging fertilization device are consistent with the field experiment results. The research results provide a certain technical reference for the optimization of the whole-film double ridge-furrow sowing technology.