Nanoindentation processes in single crystal Ag thin film under different crystallographic orientations and various indenter widths are simulated by the quasicontinuum method. The nanoindentation deformation processes under influences of crystalline anisotropy and indenter size are investigated about hardness, load distribution, critical load for first dislocation emission and strain energy under the indenter. The simulation results are compared with previous experimental results and Rice-Thomson (R-T) dislocation model solution. It is shown that entirely different dislocation activities are presented under the effect of crystalline anisotropy during nanoindentation. The sharp load drops in the load–displacement curves are caused by the different dislocation activities. Both crystalline anisotropy and indenter size are found to have distinct effect on hardness, contact stress distribution, critical load for first dislocation emission and strain energy under the indenter. The above quantities are decreased at the indenter into Ag thin film along the crystal orientation with more favorable slip directions that easy trigger slip systems; whereas those will increase at the indenter into Ag thin film along the crystal orientation with less or without favorable slip directions that hard trigger slip systems. The results are shown to be in good agreement with experimental results and R-T dislocation model solution.
The process of nanocontact including indentation and retraction between a large Ni tip and a Cu substrate is investigated using quasicontinuum (QC) method. The multiscale model reveals that significant plastic deformation occurs during the process of nanocontact between Ni tip and Cu substrate. Plastic deformation is observed in an area as large as 20 nm wide and 10 nm thick beneath Ni tip during the indentation and retraction. Also, plastic deformation at a deep position in the Cu substrate does not disappear after the neck failure. The analysis of generalized planar fault energy curve shows that there is a strong tendency for deformation twinning in Cu substrate. However, deformation twinning will be retarded during indentation due to the high stress intensity caused by stepped surface of Ni tip. The abrupt drop of load curve during tip retraction is attributed to the two different fracture mechanisms. One is atomic rearrangement near the interface of Ni tip and Cu substrate at the initial stage of neck fracture, the other is shear behavior of adjacent {111} planes at the necking point. A comparison of the critical load and critical contact radius for neck fracture is also made between theoretical values and our numerical results.
The thermal–electric bifunctional devices with isotropic and anisotropic geometries are designed in this paper, which can realize different control functions (invisible sensors and cloaks) of thermal and electric fields. We first theoretically achieve the bifunctions of invisible sensors and cloaks with isotropic and anisotropic geometries. When the material parameters of the core and matrix and the geometric parameters of the core, inner shell, and outer shell are determined, the thermal–electric invisible sensors could be realized. Meanwhile, the invisible sensors will degrade to invisible cloaks as the inner shell material is insulating. The simulations applying the derived material parameters have also been conducted to verify the thermal–electric bifunctions of different circular and confocal elliptical devices. The results show that the thermal–electric bifunctional devices can effectively control the thermal and electric fields, and these devices exhibit perfect performance of the thermal–electric functions of invisible sensors and cloaks. This work presents a new method to realize thermal–electric bifunctional devices and opens a new window to the development of multi-physics field.
In order to study the effects of kink-like defects in twin boundaries on deformation mechanisms and interaction between dislocations and defects in twin boundaries under localized load, nanotwinned Cu with two defective twin (TDT) boundaries is compared with the nanotwinned Cu with two perfect twin (TPT) boundaries, and nanotwinned Cu with single defective twin (SDT) boundary and single perfect twin boundary by simulating spherical nanoindentations using molecular mechanics. The indenter force-depth and hardness-contact strain responses were analyzed. Results show that the existence of intrinsic defects in twin boundary could reduce the critical load and critical hardness of nanotwinned material. A quantitative parameter was first proposed to evaluate the degree of surface atom accumulation around the indenter during nanoindentation, and it can be inferred that the surface morphology in TDT changes more frequently than the surface morphologies in TPT and SDT. The atomistic configurations of incipient plastic structures of three different models were also analyzed. We found that the intrinsic defects in twin boundary will affect the incipient plastic structures. The formation of twinning partial slip on the defective twin boundary happens before the contact of the dislocation and twin boundary. The kink-like defects could introduce Frank partial dislocation to the twin boundary during interaction between dislocation and twin boundary, which was not detected on the perfect twin boundary. In addition, the area of twinning partial slips on the upper twin boundary in the incipient plastic structures in SDT and TDT are larger than the twinning partial slip area in TPT, which results in the reduction of the critical hardness in SDT and TDT. The kink-like defects could also block the expansion of twinning partial slip on the twin boundary. Furthermore, we investigated the dislocation transmission processes in three different models. It is found that the dislocation transmission event could be delayed in model containing single defective twin boundary, while the transmission process could be advanced in model containing two consecutive defective twin boundaries. The quantitative analysis of dislocation length was also implemented. Result shows that the main emitted dislocation during nanoindentation is Shockley partial, and the dislocation nucleation in SDT and TDT is earlier than the dislocation nucleation in TPT due to the existence of defects. It is inferred that the intrinsic defects on twin boundaries could enhance the interaction between dislocations and twin boundaries, and could strongly change the structure evolution and promote the dislocation nucleation and emission. These findings about kink-like defects in twin boundaries show that the inherent kink-like defects play a crucial role in the deformation mechanisms and it should be taken into consideration in future investigations. Single defective twin boundary structure is recommended to delay the transmission and block the expansion of twin boundary migration. Some of the results are in good agreement with experiments.