Maritime hydraulic components are often exposed to harsh environmental conditions which can lead to accelerated deterioration, reduced function, equipment failure and costly repair. Two leading causes of maritime hydraulic failure are biofouling accumulation and corrosion. This study examined the antifouling performance of three candidate replacement high velocity oxygen fuel (HVOF) coatings relative to the performance of the current baseline air plasma spray (APS) ceramic coating for protection of hydraulic actuators. Following 20 weeks immersion at tropical and temperate field exposure sites, the control APS ceramic accumulated significantly greater levels of biofouling compared to the HVOF coatings. More specifically, the magnitude of growth of real-world nuisance hard fouling observed on in-service hydraulic components (eg calcareous tubeworms and encrusting bryozoans) was significantly greater on the APS ceramic relative to HVOF coatings. Possible explanations for the observed patterns include differences in surface topography and roughness, the electrochemical potential of the surfaces and the colour/brightness of the coatings.
3-D printing allows for rapid prototyping and manufacture of components in a cost effective and timely manner, becoming a popular technology for oceanographic and maritime engineering applications. However, 3-D printed components are at risk of accumulating marine biofouling. This study examined the antifouling (AF) performance of three Cu-containing 3-D printing polymer filaments for potential marine use. The amount of Cu present in each filament was the primary determinant of AF performance. The lowest Cu-content (30%) filament recording 29% biofouling cover after 1 month and near 100% cover after 3 months. These AF results were comparable to polylactide acid (PLA) and acrylonitrile butadiene styrene (ABS) polymer filament controls. The medium (50%) Cu-content filament remained largely free of biofouling until 3 months (where 48% coverage was observed), after which fouling cover increased to 100% by ∼12 months. The highest Cu-content (80%) filament remained free of all macrofouling for the entire 24 months of the experiment.
The biofouling of marine structures must be controlled if crippling operational and maintenance costs are to be avoided and biological invasions prevented. However, traditional methods of biofouling control typically involve the use of toxic chemicals, which have their own drawbacks, both financial and environmental. For ships, the hull is the largest surface requiring a fouling-control coating; however, there are other so-called ‘niche’ areas (up to 10% of the total wetted area) that typically cannot be, or are not routinely, treated to prevent biofouling accumulation. The use of UV light is a tried and tested sterilization method that has been shown to also work underwater. However, the speed with which UV can be applied to large-scale biofouling control will be determined by the engineering challenges involved and the lack of basic understanding of the biological mode of action. The former is essential for the effective translation of this established technology into a high-performance, industrially useful fouling-control system. The latter will be important for environmental regulation and safe use as well as performance optimisation. Here, we developed two bespoke flow-through systems to replicate ship niche areas and deployed them in Melbourne, Australia, and North East England. We demonstrated a 40–90% reduction in biofouling coverage on silicone tiles embedded with UV-emitting LEDs, even as the LED output waned (after ~8000 h). Image analysis and amplicon sequencing of 18S genes provided complementary information about the taxonomic composition of the fouling communities and highlighted some taxa, for example, ascidians and diatoms, which may have, or in the future develop, UV resistance. Interestingly, the UV treatment far exceeded performance estimates based on the predicted attenuation distance of UV in seawater. Overall, while it is clear that UV treatment works in terms of its efficacy against the vast majority of observed fouling species, technical challenges remain, as do knowledge gaps surrounding the biological and ecological effects of widespread use.
Background: Dinoflagellates are a ubiquitous and ecologically important component of marine phytoplankton communities, with particularly notable species including those associated with harmful algal blooms (HABs) and those that bioluminesce. High-throughput sequencing offers a novel approach compared to traditional microscopy for determining species assemblages and distributions of dinoflagellates, which are poorly known especially in Australian waters. Results: We assessed the composition of dinoflagellate assemblages in two Australian locations: coastal temperate Port Phillip Bay and offshore tropical waters of Davies Reef (Great Barrier Reef). These locations differ in certain environmental parameters reflecting latitude as well as possible anthropogenic influences. Molecular taxonomic assessment revealed more species than traditional microscopy, and it showed statistically significant differences in dinoflagellate assemblages between locations. Bioluminescent species and known associates of HABs were present at both sites. Dinoflagellates in both areas were mainly represented by the order Gymnodiniales (66%—82% of total sequence reads). In the warm waters of Davies Reef, Gymnodiniales were equally represented by the two superclades, Gymnodiniales sensu stricto (33%) and Gyrodinium (34%). In contrast, in cooler waters of Port Phillip Bay, Gymnodiniales was mainly represented by Gyrodinium (82%). In both locations, bioluminescent dinoflagellates represented up to 0.24% of the total sequence reads, with Protoperidinium the most abundant genus. HAB-related species, mainly represented by Gyrodinium, were more abundant in Port Phillip Bay (up to 47%) than at Davies Reef (28%), potentially reflecting anthropogenic influence from highly populated and industrial areas surrounding the bay. The entire assemblage of dinoflagellates, as well as the subsets of HAB and bioluminescent species, were strongly correlated with water quality parameters (R2 = 0.56–0.92). Significant predictors differed between the subsets: HAB assemblages were explained by salinity, temperature, dissolved oxygen, and total dissolved solids; whereas, bioluminescent assemblages were explained only by salinity and dissolved oxygen, and had greater variability. Conclusion: High-throughput sequencing and genotyping revealed greater diversity of dinoflagellate assemblages than previously known in both subtropical and temperate Australian waters. Significant correlations of assemblage structure with environmental variables suggest the potential for explaining the distribution and composition of both HAB species and bioluminescent species.