The paper describes the developed curvilinear motion simulation model for a vehicle with two traction electric motors moving on a solid surface used to study the dynamic properties of a wheeled vehicle and to subject the developed methods to virtual testing. The simulation model of the electric all-wheel drive vehicle is carried out in the Simcenter Amesim environment to account for the dynamic characteristics and features of the vehicle. The simulation model was developed based on the drawn requirements while the assumptions were justified. Inertia characteristics, tire characteristics, suspension elements, grip characteristics, and surface and air resistance were considered, as these factors affect the vehicle longitudinal and transverse dynamics. The article presents the model implemented in the “Labcar” system and confirms its adequacy by comparing it with the data obtained during the full-scale prototype tests. The bench and range tests of a test vehicle with electric transmission equipped with a measuring complex confirmed the adequacy of the developed model. The results of comparative tests allow for the conclusion that the developed model complex is suitable for modeling purposes, including studying, debugging and initial calibrations of the algorithm of torque distribution on the driving axles of all-wheel drive electric vehicle.
BACKGROUND: The development of electric and hybrid vehicles is impossible without the creation of schemes in which torque is generated by electric motors independently on the front and rear axles or on each wheel and the best dynamics is achieved. The development of a function for distributing torque between the axles or wheels of a car is a relevant technical task. AIMS: Creation of a mathematical model for the torque distribution requested by the driver to the front and rear electric motors in order to assist the course stability system and counteract wheel slip when driving in a turn close to drifting/skidding or driving on surfaces with a low or variable grip coefficient. METHODS: The algorithm model was built in the MATLAB/Simulink environment, was tested in the model-in-the-loop mode on a simulation model developed in the Simcenter Amesim environment, was tested in the hardware-in-the-loop mode on the LabCar real-time machine (ETAS GmbH) and was tested in a vehicle. RESULTS: The function based on the abovementioned methods was built in MATLAB/Simulink. Testing in simulation mode on the simulation model developed in Simcenter Amesim was performed and the initial values of calibration parameters were determined. Implementation of the function into the software structure of the prototype and compilation of the executable C-code for the master file loaded into the control unit were completed. Testing of the function implemented into the control unit on the LabCar real-time test rig was carried out. After eliminating the shortcomings identified at the previous stages of testing, calibrations and tests of the function integrated into the vehicle were carried out, which showed the effectiveness of the described torque distribution model. CONCLUSIONS: The practical value of the study lies in the possibility of using the proposed control laws to develop systems for torque distribution between the axles or wheels of modern vehicles.
BACKGROUND: The market of vehicles using electricity as an energy source demonstrates significant growth. Currently, there are more than twenty million electric vehicles worldwide. Leading manufacturers give the high priority to development of electric transport due to lower vehicle service costs, ease of driving as well as zero emissions in environment and almost complete noiselessness at motion. In addition, using the full-wheel drive in an electric vehicle makes it possible to improve off-road capability, ensures more balanced chassis control, precise following the path and constant accuracy of steering. AIMS: Ensuring increase in vehicle course stability, delivering the maximal torque regarding vehicle motion conditions and slip control in dual-motor layouts of electric vehicles. METHODS: In order to solve the given task, implementation of the special-purpose algorithm of torque distribution between driving axles of an electric vehicle is assumed. The paper presents the development of the simulation model of a vehicle, built in the Simcenter Amesim software and considering dynamic properties and features of the vehicle. This model was implemented into the Labcar hardware-in-the-loop facility. RESULTS: The simulation result is comparison with the data obtained during ground testing of the prototype and confirming the aim of simulation model development, in particular the capability of revision and preliminary setting up the algorithm of torque distribution between driving axles of a vehicle. CONCLUSIONS: Based on the results of the testing of the developed facility, it can be concluded that the developed simulation facility is suitable for solving the simulation tasks including research, debugging and primary calibrations of the algorithm of torque distribution between driving axles of a full-wheel driven electric vehicle. The errors at simulation of operation modes relevant to longitudinal and lateral dynamics of the prototype is no more than 7.5% that complies with the simulation aims.
Current trends in the development of the automotive industry are aimed at improving energy efficiency, environmental friendliness and safety of vehicles. One of the key directions in this area is the development of all-wheel drive electric vehicles with individual electric drives. This architecture allows not only improving the dynamic characteristics of a vehicle, but also implementing complex control systems such as torque control in order to adjust cornering and to increase directional stability. In English-language sources, such systems are called Torque Vectoring (TV). These systems can significantly improve its stability and handling, especially in difficult road conditions such as icy or wet surfaces. The aim of the work is a comparative analysis of various controllers used to control the torque in electric vehicles with individual electric drives for the left and right wheels. This paper considers various approaches to torque control, including both classical control methods such as controllers, and more advanced control methods such as first- and second-order sliding control modes, integral sliding mode, and fuzzy logic controllers. In addition, the paper discusses the control errors that are used to generate the torque, such as the yaw rate, the side slip angle, and the ratio of the axles’ velocities. The paper contains an in-detail description of the principles of operation of each of the controllers, their advantages and disadvantages are noted, attention is directed to the problem of “rattling” in sliding modes and scenarios of incorrect control by error of the axles’ velocities. To assess the effectiveness of control methods, a weighted control efficiency index was used, which takes into account the accuracy of tracking yaw rate, minimizing the side slip angle, and the degree of control action. It was found that most of the published assessments of the effectiveness of the proposed control methods were based on simulation results. Therefore, a need for further research, including tests on real vehicles and an assessment of the impact of the rattling effect on the operation of electric drives, remains.