The paper presents a simulation of the Airbus A350-900 wing-to-fuselage assembly process. The latter is a complex multistage process where the compliant parts are being joined by riveting. The current research analyzes the quality of the temporary fastener arrangement. The fastener arrangement is being checked to ensure that the residual gap between joined parts is small, and the fastener loads closing the gap are calculated. The deviations of the part shape from nominal are modeled via initial gaps. A cloud of initial gaps is generated based on the statistical analysis of the available measurements assuming the stochastic nature of local gap roughness. Through the reduction of the corresponding contact problem to a quadratic programming (QP) problem and the use of efficient QP algorithms together with the task-level parallelism, the mass contact problem solving on refined grids is accomplished.
18 September 2020 in Optimization Methods and Software
In this paper, we consider Newton projection method for solving the quadratic programming problem that emerges in simulation of joining process for assembly with compliant parts. This particular class of problems has specific features such as an ill-conditioned Hessian and a sparse matrix of constraints as well as a requirement for the large-scale computations. We use the projected Newton method with a quadratic rate of convergence and suggest some improvements to reduce the solving time: a method for solving the system of linear equations, so-called constraint recalculation method, and compare different approaches for step-size selection. We use the duality principle to formulate alternative forms of the minimization problem that, as a rule, can be solved faster. We describe how to solve the considered nonlinear minimization problem with the nonsmooth objective function by modifying Newton projection method and employing subgradients. In addition, we prove the convergence of the suggested algorithm. Finally, we compare Newton projection method with the other quadratic programming techniques on a number of assembly simulation problems.
7 May 2024 in The International Journal of Advanced Manufacturing Technology
The variation analysis is a key tool for ensuring the high quality assembly in the process of developing the technology for manufacturing of aircraft parts. One of the main factors in variations is the deviations in the positioning procedure. This paper is devoted to the development of an approach that allows taking into account the variations during positioning and merging it with the special algorithm of contact problem solving. The impact of varied boundary conditions is incorporated into an additional vector of forces that can be interpreted as reactions to the shift of supports. The obtained results are illustrated with a case of wing-to-fuselage assembly.
7 February 2022 in Journal of Computing and Information Science in Engineering
Riveting and bolting are common assembly methods in aircraft production. The fasteners are installed immediately after hole drilling and fix the relative tangential displacements of the parts that took place. A proper fastener sequence installation is very important because a wrong one can lead to a “bubble-effect” when gap between parts after fastening becomes larger in some areas rather than being reduced. This circumstance affects the quality of the final assembly. For that reason, the efficient methods for determination of fastening sequence taking into account the specifics of the assembly process are needed. The problem is complicated by several aspects. First of all, it is a combinatorial problem with uncertain input data. Second, the assembly quality evaluation demands the time-consuming computations of the stress–strain state of the fastened parts caused by sequential installation of fasteners. Most commonly used strategies (heuristic methods and approximation algorithms) require a large number of computational iterations what dramatically complicates the problem. The paper presents the efficient methods of fastener sequence optimization based on greedy strategy and the specifics of the assembly process. Verification of the results by comparison to commonly used installation strategies shows its quality excellence.
This paper is devoted to the development of a numerical approach that allows quick detection of the conditions favorable for the beginning of noticeable vibrations during drilling. The main novelty of the proposed approach lies in taking into account the deviations of the assembled compliant parts during non-stationary contact analysis by means of variation simulation. The approaches to stationary analysis of assembly quality are expanded and generalized for modeling such non-stationary effects as vibration and resonance. The numerical procedure is based on modeling the stress–strain state of the assembled structures by solving the corresponding transient contact problem. The use of Guyan reduction, the node-to-node contact model and the application of the generalized α method allow the reformulation of the contact problem in terms of a series of quadratic programming problems. The algorithm is thoroughly tested and validated with commercial software. The efficiency of the developed numerical procedure is illustrated by analysis of the test joints of two aircraft panels. The unsteady process of drilling the panels with periodic drilling force was simulated. The influence of deviations in the shape of the parts on the non-stationary interlayer gap was modeled by setting different initial gaps between parts. It is shown that the oscillation amplitudes of the interlayer gap depend on the initial gaps and do not correlate with the mean value of the stationary residual gap. Thus, non-stationary analysis provides new information about the quality of the assembly process, and it should be applied if the assembly process includes periodic impact on the assembled parts.