The application of horizontal well volume fracturing technology is an important method for enhancing oil recovery in tight oil reservoirs. However, the influence mechanism of the fracture placement scheme (FPC) on postfracturing productivity is still unclear. Based on the theory of the black oil model, combined with the reservoir stimulation characteristics of horizontal well volume fracturing in tight oil reservoirs, this paper established a postfracturing reservoir production simulation model. History fitting was used to verify the accuracy of the production model simulations. A series of numerical simulations was carried out to study the influence mechanisms of the fracture parameters and FPC on productivity. The simulation results show that compared with the fracture conductivity, the fracture length and number are the main parameters affecting tight oil reservoir productivity. Selecting a reasonable fracture length and number can realize the economical and efficient production of tight oil reservoir volume fracturing. Compared with the traditional fracture equal-length scheme, an FPC with an uneven fracture length can increase the cumulative oil production of oil wells. Under the condition of the same total fracture length, the scheme with a staggered distribution of long fractures and short fractures has the largest cumulative oil production over five years. A reasonable well spacing can greatly reduce the impact of interwell interference on postfracturing dual branch horizontal well productivity. When dual branch horizontal well fractures are alternately distributed, the postfracturing productivity is higher. The production simulation model established in this paper provides a method to accurately evaluate the productivity of horizontal wells after volume fracturing, which can provide guidance for the optimization of hydraulic fracturing operation parameters.

Tight sandstone gas reservoirs are rich in reserves and are an important part of unconventional oil and gas resources. However, natural fractures’ impact on hydraulic fracture propagation behavior and network formation mechanisms remain unclear. Exploring how to optimize fracturing parameters to maximize post-fracturing productivity requires further investigation. Therefore, this study focused on the characteristics of tight sandstone gas reservoirs and established a three-dimensional numerical simulation model for hydraulic fracture propagation and post-fracturing productivity using production history matching to validate the reliability of the model. Based on this model, this study investigated the influence mechanisms of natural fracture angles, density, and lengths on hydraulic fracture propagation behavior and network formation. The spatial distribution of hydraulic fracture widths in three dimensions is also explored. When natural fracture angles are lower, a greater number of natural fractures are activated, leading to more developed secondary hydraulic fractures and the formation of complex fracture networks. Hydraulic fractures tend to penetrate directly through high-angle natural fractures. Single-well cumulative gas production increases initially with increasing natural fracture angles, then decreases, but increases with higher natural fracture density and length. Optimal fracturing in areas with longer natural fractures, lower angles, and higher density distribution enhances single-well productivity effectively.

A conventional oil and gas well does not have a natural production capacity, which necessitates a hydraulic fracturing operation. The effectiveness of the fracturing directly impacts the economic benefit of a single well. Among the various parameters, including fracture spacing, fracture width, and conductivity, fracture half-length is one of the main influencing factors on the productivity of horizontal wells. For conventional homogeneous reservoirs, research mainly focuses on fracture patterns with equal fracture lengths. However, in actual production processes, due to mutual interference and the superimposition of drainage areas between fractures, the production distribution of each fracture is non-uniform. Typical fracture distribution patterns mainly include uniform, staggered, dumbbell, and spindle. While many believe that the dumbbell-shaped fracture distribution pattern has the best effect, there has been no quantitative study on the length of each fracture under the dumbbell-shaped pattern. Based on this, this paper proposes a modeling approach for function-shaped fracture distribution that takes advantage of the high production of edge fractures and the low output of middle fractures in horizontal wells. The influence of this approach on production capacity is studied. Constant, linear, and parabolic functions are used to establish the relationship between fracture position and fracture half-length, optimizing the fracture distribution function to achieve the best production effect. This method can guide the horizontal well fracture distribution in the block to maximize productivity. The results show that the parabolic function-shaped model is better than the linear function-shaped model and the constant function-shaped model is the least effective. The research presented in this paper offers a new idea for optimizing on-site fracturing plans. It utilizes mathematical expressions to describe the parameters that affect productivity, which provides valuable guidance for designing multi-stage fractured horizontal wells in the field. In the future, this research will be extended by exploring the optimal fracture distribution function under different formation conditions.

It is not clear how the distribution of retained fracturing fluids and its effect on the permeability and wettability in tight oil reservoirs interact. Especially, there are more qualitative studies and less quantitative studies on this issue. Under laboratory experimental conditions, this paper clarifies the distribution of retained fracturing fluids in the core and reveals the influence rule of retained fracturing fluids on tight reservoir permeability and wettability. It is found that the main retention space of retained fracturing fluids in a tight reservoir is a microporous interval, and the residual oil after oil displacement by retained fracturing fluids mainly exists in the core in the form of dots or porphyries. The smaller permeability and porosity of the core will lead to more retained fracturing fluids. The permeability of different cores after fracturing fluid retention has decreased to varying degrees compared with that before fracturing fluid retention. The wettability of core slices before and after fracturing fluid retention was tested, and the effect of retained fracturing fluids on reservoir wettability was not significant. This study has important significance for improving the recovery of tight oil reservoirs and enhancing the understanding of postfracturing fluid retention.