Xiaochen Xie

Prof. Xiaochen Xie


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 May 2024 in Materials
Verified
Journal Article
Open access
PDF file
XZXiuchen Zhao
Xiuchen Zhao
JCJiahui Chang
Jiahui Chang
XWXuefeng Wu
Xuefeng Wu
ZYZi-Ting Ye
Zi-Ting Ye
WCWeiwei Chen
Weiwei Chen
XXXiaochen Xie
Xiaochen Xie
SnPb solder was widely used in electronic packaging for aerospace devices due to its high reliability. However, its creep resistance is poor and can be improved by adding alloying elements. The effects of Sb content on the microstructure, tensile, and creep properties of eutectic SnPb solder were investigated. Sb addition effectively improved the mechanical properties of the SnPb solder. When Sb content exceeds 1.7 wt.%, SbSn intermetallic compounds (IMCs) occurred. And increasing the Sb content increased the tensile strength. Furthermore, Sb addition decreased the steady-state creep rate and increased the stress exponent n, suggesting that the creep resistance had been enhanced, which may be attributed to the hindrance of dislocation movement by SbSn IMCs, as well as the reduction in phase boundaries, which consequently reduced grain boundary sliding.

18 February 2025 in Materials
Verified
Journal Article
Open access
PDF file
XXXiaochen Xie
Xiaochen Xie
PLPengrong Lin
Pengrong Lin
BLBinhao Lian
Binhao Lian
SXShimeng Xu
Shimeng Xu
YWYong Wang
Yong Wang
XZXiuchen Zhao
Xiuchen Zhao
In this paper, In was introduced into SnPb eutectic solder to develop a new low-temperature solder for three-dimensional packaging technology. SnPbIn solders containing 5, 10, 13, 15 and 17 wt.% In were prepared through vacuum induction melting. The effect of the addition of In on the microstructure and thermal and mechanical properties of the SnPbIn solders was investigated. The results showed that the SnPb eutectic solder consisted of Sn(ss) and Pb(ss), but when the In content was higher than 5 wt.%, the SnPbIn solder included Sn(ss) and Pb(ss) and a new InSn4 phase. Solid dissolution of the In element into Sn(ss) and Pb(ss) preferentially occurred. The melting points of the SnPbIn solders gradually decreased with the increasing addition of the In element. The melting point of the Sn-Pb-13In solder decreased to 150.5 °C, which met the requirements of 2.5D packaging. But the cast Sn-Pb-5In solder reached the best tensile strength of 48.8 MPa and elongation of 27.3%. Super-plasticity occurred in the cold-rolled SnPbIn, while the 59.9Sn35.1 Pb5In solder achieved elongation of 382.0% and 408.6%, respectively, at deformation of 70% and 90%. The super-plasticity originated from the recrystallization behavior and soft orientation.

2 February 2024 in Materials
Verified
Journal Article
Open access
PDF file
ZQZhibo Qu
Zhibo Qu
YHYilong Hao
Yilong Hao
CCChanghao Chen
Changhao Chen
YWYong Wang
Yong Wang
SXShimeng Xu
Shimeng Xu
XXXiaochen Xie
Xiaochen Xie
PbSn solders are used in semiconductor devices for aerospace or military purposes with high levels of reliability requirements. Microalloying has been widely adopted to improve the reliability for Pb-free solders, but its application in PbSn solders is scarce. In this article, the optimization of PbSn solder reliability with Ge microalloying was investigated using both experimental and calculation methods. Intermetallic compounds (IMC) growth and morphologies evolution during reliability tests were considered to be the main factors of device failure. Through first-principle calculation, the growth mechanism of interfacial Ni3Sn4 was discussed, including the formation of vacancies, the Ni-vacancies exchange diffusion and the dominant Ni diffusion along the [1 0 0] direction. The doping of Ge in the cell increased the exchange energy barrier and thus inhibited the IMC development and coarsening trend. In three reliability tests, only 0.013 wt% Ge microalloying in Pb60Sn40 was able to reduce IMC thickness by an increment of 22.6~38.7%. The proposed Ge microalloying method in traditional PbSn solder could yield a prospective candidate for highly reliable applications.

31 August 2024 in Materials Today Communications
Verified
Journal Article
Closed access
ZYZi-Ting Ye
Zi-Ting Ye
XZXiuchen Zhao
Xiuchen Zhao
XXXiaochen Xie
Xiaochen Xie
JCJiahui Chang
Jiahui Chang
WCWeiwei Chen
Weiwei Chen