The purpose of this study was to characterize the etching mechanism, namely, the etching rate and the activation energy, of a titanium dental implant in concentrated acid and to construct the relation between the activation energy and the nanoscale surface topographies. A commercially-pure titanium (CP Ti) and Ti-6Al-4V ELI surface were tested by shot blasting (pressure, grain size, blasting distance, blasting angle, and time) and acid etching to study its topographical, weight loss, surface roughness, and activation energy. An Arrhenius equation was applied to derive the activation energy for the dissolution of CP Ti/Ti-6Al-4V ELI in sulfuric acid (H2SO4) and hydrochloric acid (HCl) at different temperatures. In addition, white-light interferometry was applied to measure the surface nanomorphology of the implant to obtain 2D or 3D roughness parameters (Sa, Sq, and St). The nanopore size that formed after etching was approximately 100–500 nm. The surface roughness of CP Ti and Ti-6Al-4V ELI decreased as the activation energy decreased but weight loss increased. Ti-6Al-4V ELI has a higher level of activation energy than Ti in HCl, which results in lower surface roughness after acid etching. This study also indicates that etching using a concentrated hydrochloric acid provided superior surface modification effects in titanium compared with H2SO4.
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
Hydroxyapatite (HA) coatings on titanium have been investigated for many years, and have demonstrated advantageous biocompatibility in dental implants. Animal experiments have demonstrated that the biological response to plasma-sprayed HA-coated implants shows disadvantages in terms of adherence, thickness uniformity, and long-term osseointegration effects. Determining how to resolve the degradation problem of HA in the body by improving osseointegration and stability in alveolar bones has become an increasingly researched topic. The present study investigated the film characteristics and dissolution properties of calcium phosphate (CaP) coatings obtained by radio-frequency (RF) sputtering of a self-developed atmospheric plasma spray (APS) HA target. The experimental parameters varied, including RF power (60–250 W), sputtering time (15–120 min), and substrate roughness (0.4–4 μm). Analyses were conducted using synchrotron X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), white light interferometry, and scanning electron microscopy combined with energy-dispersive X-ray spectroscopy (EDS). EDS analysis showed that the Ca/P ratio increased as the discharge power was increased. The analysis results also showed that a lower surface roughness resulted in higher crystallinity, because a larger surface-free energy was attained during sputtering. In-plane texturing has been proven when HA films are sputtered onto substrates of varying roughness, within appropriate deposition parameters. FTIR analysis revealed the presence of the principal PO43- bonds in the deposited calcium phosphate films. The CaP films induced calcium phosphate precipitation when immersed in simulated body fluid (SBF), suggesting that, based on in vitro bioactive behavior, the proposed combined surface modification can be used in dental implants.
The influences of reactive and dielectric characteristics of activators were investigated in the microwave-catalyzed conversion of phenolic resin waste to activated carbon (AC). To compare with the dielectric interactions of the microwaves with treated samples, conventional electric heating for AC carbonization was also conducted in parallel. The porosity and chemical features of the prepared AC were examined, and the AC was used to remove ammonium from water through adsorption. The results revealed that KOH-activated wastes developed a highly porous structure, whereas H3PO4 treated wastes were functionalized with surficial phosphate groups. Both of these features were more pronounced in the cases of microwave-catalyzed carbonization than those using conventional electric heating. Because of the intense dielectric interactions of the H3PO4-activated waste with microwave, the abundant phosphate functional groups formed on the phenolic resin waste surface during microwave-catalyzed carbonization. They facilitated the resulting AC as an effective adsorbent for aqueous ammonium.
The purpose of this study was to explore the properties of sintered hydroxyapatite specimens for developing a suitable hydroxyapatite target and a fabrication process for the radio frequency sputtering of implants. Using a compound surface treatment of sand blasting and acid etching followed by hydroxyapatite radio frequency sputtering, this work planned to develop a commercial dental implant system in the near future. First, in addition to producing hydroxyapatite parts using hot isostatic pressing, this study examined the properties of hydroxyapatite parts produced through cold pressing followed by sintering in vacuum and air. The experimental results showed that the index of crystallization, density, and Vickers hardness of the parts sintered in air were more favorable than those of parts sintered in vacuum, and that the parts sintered in vacuum could crack or break. Second, hydroxyapatite sputtering was performed on the hot isostatic pressing–produced and cold pressing–produced targets on titanium dental implant surfaces at power levels of 50 and 90 W. The results showed no cracks in the cold pressing–produced hydroxyapatite targets when the sintering condition was at 1050 °C. By contrast, cracks occurred in the hot isostatic pressing hydroxyapatite targets at a relative density in excess of 93.35%. Observing scanning electron microscopy cross-sectional images revealed that the sputtering deposition rate was approximately 0.456 nm/min at the sputtering power level of 50 W and 1.139 nm/min at 90 W.