Ezzeddine Ftoutou

Dr. Ezzeddine Ftoutou

National Engineering School of Monastir, University of Monastir, Monastir, Tunisia
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 August 2011 in Transactions of the Institute of Measurement and Control
Verified
Journal Article
Closed access
PDF file
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
MCMnaouar Chouchane
Mnaouar Chouchane
NBNoureddine Besbès
Noureddine Besbès
This paper investigates the classification of a valve clearance fault in an internal combustion diesel engine using vibration time domain features extracted from signal segments measured at several points on the engine bloc. Signals containing a large number of engine cycles are used to obtain a number of observations of each feature. The set of features is thus considered a set of variables. A stepwise variable selection algorithm based on univariate and multivariate analysis of variance is then used to sort the variables according to their diagnostic ability. The algorithm is also used to construct sets of variables of increasing size used to improve fault classification. Four commonly used supervised classifiers are trained and then tested, giving roughly the same percentage of correct classification. The tested classifiers confirmed that the use of more variables selected by the stepwise variable selection algorithm increases the percentage of correct classification.

19 January 2024 in Materials
Verified
Journal Article
Open access
PDF file
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
LALamis Allègue
Lamis Allègue
HMHaykel MAROUANI
Haykel MAROUANI
THTarek Hassine
Tarek Hassine
Yasser FouadYasser Fouad
Yasser Fouad
HMHatem Mrad
Hatem Mrad
Nowadays, 3D PLA-printed parts are widely used in many applications, essentially using the fused filament fabrication technique. While the influence of printing parameters on quasi-static mechanical characterization has been extensively considered within the literature, there are limited accounts of this effect on fatigue performance. The two main aims of this research are first to investigate the effects of the infill density percentage on the fatigue life of dog-bone samples under rotating bending cycling loads, and second to model the fatigue life using Wöhler and Basquin models. The experiments exhibit a high variability of results, especially for low cyclic loads. The S–N curves show that the number of cycles at failure increases with the increase in the infill density percentage and decreases with the increase in loads. Investigations allow the formulation of each constant model as a function of the infill density percentage. The new fatigue model formulations exhibit good agreement with the experimental data. As an outcome of this study, the fatigue model for 3D-printed parts may be expressed as a function of the infill density percentage using fewer tests in the future and for other polymers used in fused filament fabrication.

25 November 2017 in Lecture Notes in Mechanical Engineering
Verified
Book Chapter
Closed access
PDF file
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
MCMnaouar Chouchane
Mnaouar Chouchane

14 May 2019 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
PDF file
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
MCMnaouar Chouchane
Mnaouar Chouchane
By using the unsupervised fuzzy clustering, this study attempts to design a new scheme for the unsupervised detection and classification of two injection faults using the time–frequency analysis of vibration signals of an internal combustion, four-stroke, diesel engine with six cylinders in-line. To reach this objective, two new methods called modified S-transform and two-dimensional non-negative matrix factorization are used. Three fuzzy clustering algorithms and nine cluster validity indices, for a variable number of classes, are also used to detect and classify the fault classes. The implementation of these methods resulted in a high detection rate of the injection faults.

1 August 2023 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
AFAhmed Seifallah Frih
Ahmed Seifallah Frih
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
AKAted BEN KHALIFA
Ated BEN KHALIFA
MTMoez Trigui
Moez Trigui
Fe-Ni alloys present excellent heat resistance properties while preserving their rigidity, strength, toughness, and dimensional stability at high temperatures. As a result, they are widely used in manufacturing aerospace or aeronautic parts where the operating temperature is very close to their melting temperature. Supra50 (named in the Unified Numbering System UNS as K94800) is a Fe-Ni alloy currently used in space and aviation industries, which confirmed its efficiency. However, improving the surface roughness of this high-precision part is challenging to overcome in manufacturing. The main objective of this study is to carry out an experiment based on a factorial plan and aims to predict the surface roughness of Supra50 parts as a function of cutting parameters in a milling process. Results show that the best combination of cutting parameters, giving the best surface roughness, is obtained at the lowest value of feed per tooth. Results also show that cutting speed and radial depth have little effect on roughness quality.

6 May 2024 in Matériaux & Techniques
Verified
Journal Article
Closed access
PDF file
MRMounir Rabhi
Mounir Rabhi
AKAted BEN KHALIFA
Ated BEN KHALIFA
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
SCSami Chatti
Sami Chatti
The control of the heat input and the geometrical characteristics of the joint during and after a layer deposition remains the concern of the manufacturers in Wire Arc Additive Manufacturing, despite the existence of all new technologies such as the Cold Metal Transfer process. The understanding of the effect of arc parameters having a remarkable role in the optimization of the layer deposition heat input is essential. In the following work, we will focus on the influence of the combination of the parameters of Cold Metal Transfer arc length and arc dynamics correction on the geometrical and mechanical characteristics of the final weld bead. Experimental and statistical investigations have been carried out on F57 filler metal for the assembly of S235 thin metal sheets by the butt joining method using the universal Cold Metal Transfer mode. The main parameters: (i) Arc length correction and (ii) Dynamic Arc correction have been varied to investigate the effect of the combination of these parameters using surface response from experimental plan methods under Minitab software. Furthermore, mechanical investigation using tensile tests coupled with Digital Image Correlation analysis has been realized. The obtained results show that the variation of arc length correction affects considerably the geometrical and mechanical characteristics of the one-layer deposition. However, the effect of the variation of the dynamic arc correction doesn’t affect the width of the welded bead but more the penetration. In the same way, the optimization of the arc’s length enabled us to control the wall’s width and appearance. In addition, optimizing the arc’s dynamics enabled us to control the right blend between layers. These results contribute to the optimization of the Wire Arc Additive Manufacturing-Cold Metal Transfer process parameters for future applications.