Kalpathy B. Sundaram

Prof. Dr. Kalpathy B. Sundaram


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2021 in Coatings
Verified
Journal Article
Open access
PDF file
ASAshwin Kumar Saikumar
Ashwin Kumar Saikumar
Sreeram SundareshSreeram Sundaresh
Sreeram Sundaresh
Shraddha Dhanraj NehateShraddha Dhanraj Nehate
Shraddha Dhanraj Nehate
KSKalpathy B. Sundaram
Kalpathy B. Sundaram
Thin films of CuGa2O4 were deposited using an RF magnetron-sputtering technique for the first time. The sputtered CuGa2O4 thin films were post-deposition annealed at temperatures varying from 100 to 900 °C in a constant O2 ambience for 1.5 h. Structural and morphological studies were performed on the films using X-ray diffraction analysis (XRD) and a Field Emission Scanning Electron Microscope (FESEM). The presence of CuGa2O4 phases along with the CuO phases was confirmed from the XRD analysis. The minimum critical temperature required to promote the crystal growth in the films was identified to be 500 °C using XRD analysis. The FESEM images showed an increase in the grain size with an increase in the annealing temperature. The resistivity values of the films were calculated to range between 6.47 × 103 and 2.5 × 108 Ωcm. Optical studies were performed on all of the films using a UV-Vis spectrophotometer. The optical transmission in the 200–800 nm wavelength region was noted to decrease with an increase in the annealing temperature. The optical bandgap value was recorded to range between 3.59 and 4.5 eV and showed an increasing trend with an increase in the annealing temperature.

22 January 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Sreeram SundareshSreeram Sundaresh
Sreeram Sundaresh
ABAkash Hari Bharath
Akash Hari Bharath
KSKalpathy B. Sundaram
Kalpathy B. Sundaram
For the first time, the deposition of CuCrO2 thin films was carried out using a dual-target RF magnetron sputtering technique using Cu2O and Cr2O3 targets. The deposited films were subsequently annealed in N2 ambiance from 600–900 °C. This work reports that the electrical, optical, structural, and morphological properties of CuCrO2 thin films are significantly affected due to the variation in the annealing temperature. XRD analysis confirms the presence of single-phase CuCrO2 in the films annealed at 650 °C. The presence of Cu in the 1+ oxidation state in the phase pure CuCrO2 thin films was confirmed through XPS analysis. Further, through XPS analysis, the oxidation states of Cu and Cr, the full-width half maximum (FWHM), the peak positions, and their respective binding energies have been elucidated. SEM analysis confirms the promotion of nanocrystalline growth in the thin films as the annealing temperature was increased from 600 °C. The average grain size increased from 40.22 nm to 105.31 nm as the annealing temperature was increased from 600 to 900 °C. Optical studies conducted in the wavelength range of 200 nm to 800 nm revealed a decrease in the optical transmission and optical bandgap with an increase in the annealing temperature. The highest optical transmission of ~81% and an optical bandgap of 3.21 eV were obtained for the films depicting the delafossite nature of CuCrO2. The optical bandgap was found to vary between 3.16 eV and 3.74 eV for the films studied in this research. The lowest resistivity of 0.652 Ω cm was obtained for the films annealed at 650 °C. Transparent heterojunction diodes involving p-type delafossite copper chromium oxide (CuCrO2) and n-type indium tin oxide (ITO) were fabricated. The best diode depicted a cut-in voltage of 0.85 V, a very low leakage current of 1.24 x 10-8, an ideality factor of 4.13, and a rectification ratio of 2375.

9 February 2023 in Coatings
Verified
Journal Article
Open access
PDF file
Sreeram SundareshSreeram Sundaresh
Sreeram Sundaresh
ABAkash Hari Bharath
Akash Hari Bharath
KSKalpathy B. Sundaram
Kalpathy B. Sundaram
For the first time, the effect of Cuprous Oxide (Cu2O) sputtering power variation on the radio frequency sputtered Copper Chromium Oxide (CuCrO2) thin films was studied. In this work, the sputtering power of Cr2O3 was held constant at 200 W while the sputtering power of the Cu2O target was varied from 10 to 100 W. The films were subsequently annealed at 650 °C in N2 ambiance. The effects of Cu2O sputtering power variation on the structural, optical, and electrical properties of the films have been reported in this work. X-ray diffractometer (XRD) study revealed that the single-phase delafossite structure of CuCrO2 was only obtained at Cu2O sputtering power of 50 W. X-ray photoelectron spectroscopy (XPS) analysis further established the results of XRD study where Cu in 1+ oxidation state was identified in thin films obtained at 50 W of Cu2O sputtering power. The optical studies were conducted in this work on all the post-deposition annealed films in the wavelength range of 200–800 nm. The energy dispersive x-ray spectroscopy (EDS) study revealed a near stoichiometric composition ratio of 1:1.06 of Cu:Cr at% obtained in the films sputtered with 50 W of Cu2O sputtering power. The highest optical transmission of ~81% and the highest optical bandgap of 3.21 eV were observed for single-phase CuCrO2 thin films. The optical transmission and the optical bandgap were found to decrease with an increase in the Cu2O sputtering power. The electrical study performed on all the post-deposition annealed films revealed that the lowest resistivity of 0.652 Ω-cm was identified for single-phase CuCrO2 thin films obtained at 50 W of Cu2O sputtering power.

9 February 2021 in Coatings
Verified
Journal Article
Open access
PDF file
Shraddha Dhanraj NehateShraddha Dhanraj Nehate
Shraddha Dhanraj Nehate
ASAshwin Kumar Saikumar
Ashwin Kumar Saikumar
KSKalpathy B. Sundaram
Kalpathy B. Sundaram
Amorphous hydrogenated boron carbide films were deposited on silicon and glass substrates using radio frequency sputtering. The substrate temperature was varied from room temperature to 300 °C. The substrate temperature during deposition was found to have significant effects on the electrical and optical properties of the deposited films. X-ray photoelectron spectroscopy (XPS) revealed an increase in sp2-bonded carbon in the films with increasing substrate temperature. Reflection electron energy loss spectroscopy (REELS) was performed in order to detect the presence of hydrogen in the films. Metal-insulator-metal (MIM) structure was developed using Al and hydrogenated boron carbide to measure dielectric value and resistivity. Deposited films exhibited lower dielectric values than pure boron carbide films. With higher substrate deposition temperature, a decreasing trend in dielectric value and resistivity of the films was observed. For different substrate temperatures, the dielectric value of films ranged from 6.5–3.5, and optical bandgap values were between 2.25–2.6 eV.

31 December 2022 in Coatings
Verified
Journal Article
Open access
PDF file
JPJustin Ryan Phelps
Justin Ryan Phelps
ASAshwin Kumar Saikumar
Ashwin Kumar Saikumar
Reza AbdolvandReza Abdolvand
Reza Abdolvand
KSKalpathy B. Sundaram
Kalpathy B. Sundaram
For the first time in the literature, the material properties of gallium-doped zinc oxide, grown from a high impulse magnetron sputtering system (HiPIMS), are reported. These material properties are compared to those of a typical radio frequency (RF) sputtering deposition. The films were grown without thermal assistance and were compared across multiple average deposition powers. The films’ resistivity, crystallinity, absorption coefficient, band gap, and refractive index were measured for each of the samples. It was observed that very similar results could be obtained between the HiPIMS and RF sputtering processes under the same average power conditions. It was found that the RF depositions demonstrated a slightly higher band gap and deposition rate as well as lower resistivity and optical absorption coefficient. Band gaps and grain size were found to increase with the power of the deposition for both HiPIMS and RF. These values ranged between 3.45 eV and 3.79 eV and 9 nm and 23 nm in this study, respectively. The absorption coefficient and resistivity were both found to decline with increasing power in both methods but reached minimums of 2800 cm−1 and 0.94 mOhm-cm, respectively, when sputtered using an RF power supply.

1 April 2024 in Materials
Verified
Journal Article
Open access
PDF file
ABAkash Hari Bharath
Akash Hari Bharath
ASAshwin Kumar Saikumar
Ashwin Kumar Saikumar
KSKalpathy B. Sundaram
Kalpathy B. Sundaram
CuGaO2 thin films were deposited using the RF magnetron sputtering technique using Cu2O and Ga2O3 targets. The films were deposited at room temperature onto a quartz slide. The sputtering power of Cu2O remained constant at 50 W, while the sputtering power of Ga2O3 was systematically varied from 150 W to 200 W. The films were subsequently subjected to annealing at temperatures of 850 °C and 900 °C in a nitrogen atmosphere for a duration of 5 h. XRD analysis on films deposited with a Ga2O3 sputtering power of 175 W annealed at 900 °C revealed the development of nearly single-phase delafossite CuGaO2 thin films. SEM images of films annealed at 900 °C showed an increasing trend in grain size with a change in sputtering power level. Optical studies performed on the film revealed a transmission of 84.97% and indicated a band gap of approximately 3.27 eV. The film exhibited a refractive index of 2.5 within the wavelength range of 300 to 450 nm.