Andrii Yunda

Dr. Andrii Yunda

orcid

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in Acta Physica Polonica A
Verified
Journal Article
Closed access
AGAlexander Goncharov
Alexander Goncharov
AYAndrii Yunda
Andrii Yunda
HKH. Komsta
H. Komsta
PRPrzemysław Rogalski
Przemysław Rogalski

1 March 1998 in Physica B: Condensed Matter
Verified
Journal Article
Closed access
SDS.I Denisov
S.I Denisov
AYAndrii Yunda
Andrii Yunda

5 March 2020 in SN Applied Sciences
Verified
Journal Article
Open access
PDF file
VBVladimir Buranich
Vladimir Buranich
APAlexander Pogrebnjak
Alexander Pogrebnjak
PBPiotr Budzyński
Piotr Budzyński
ISIgor Shelest
Igor Shelest
APAdam Prószyński
Adam Prószyński
AYAndrii Yunda
Andrii Yunda
Fabrication and development of HfB2-based nanostructured coatings was investigated. All films were deposited on stainless-steel substrates by RF magnetron sputtering from stochiometric HfB2 target in argon atmosphere. The aim of this work is to evaluate the effects of the bias potential on the microstructure, mechanical and tribological properties. These parameters strongly depend on the experimental conditions. X-ray diffraction analysis indicated the difference in microstructure: from dense hexagonal structure with (0001) preferred orientation of nanocrystallites to quasi-amorphous with blurred HfB2 phase peaks. All coatings were measured using nanoindentation (using Berkovich tip), tribology (ball-on-disk) and nano-scratch (friction). Coatings with a thickness of 1–2 µm had a significant dependence of properties on the microstructure: hardness drastically increased from 8 to 45 GPa, H/E ratio and elastic recovery changed respectively: 0.04–0.15 and 0.26–0.72.

1 January 2018 in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
Verified
Journal Article
Closed access
PDF file
APAlexander D. Pogrebnjak
Alexander D. Pogrebnjak
AGAlexander Goncharov
Alexander Goncharov
AYAndrii Yunda
Andrii Yunda
ISIgor Shelest
Igor Shelest
AŚAntoni Świć
Antoni Świć
ILIhor Lebedynskyi
Ihor Lebedynskyi
A comparative analysis of the microstructure and properties of coatings has been made based on multicomponent and high-entropy transition metal nitride films, depending on the deposition conditions (temperature, bias potential, partial pressure, etc.). The structural features of the films have been analyzed. The general regularities of hard and superhard nanostructured nanocomposite coatings consisting of a columnar structure and texture growth were identified. The influence of the structural state on the change of the physical and mechanical properties of nanostructured coatings based on multicomponent and high-entropy transition metal nitride films has been found.

1 January 2020 in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
Verified
Journal Article
Closed access
PDF file
AGAlexander Goncharov
Alexander Goncharov
AYAndrii Yunda
Andrii Yunda
EMEvgenii Mironenko
Evgenii Mironenko
Liudmyla VasylievaLiudmyla Vasylieva
Liudmyla Vasylieva
DBDmitrii Belous
Dmitrii Belous
The influence of the multilayer coating on the thermal load of the cutting tool was investigated. Using mathematical simulation methods, the heat flow propagation in a coated cutting tool was presented. The thermal insulation effect arising in the multilayer coating with the Al2O3 ceramic layer was considered. The analysis of thermal protection effect of such coatings at different cycles of material processing was made. The basic tribotechnical characteristics of coatings, which make a significant contribution to reducing the thermal load on the cutting plate, have been established.

1 January 2018 in High Temperature Material Processes: An International Quarterly of High-Technology Plasma Processes
Verified
Journal Article
Closed access
PDF file
AGAlexander Goncharov
Alexander Goncharov
AYAndrii Yunda
Andrii Yunda
EMEvgenii Mironenko
Evgenii Mironenko
DBDmitrii Belous
Dmitrii Belous
Liudmyla VasylievaLiudmyla Vasylieva
Liudmyla Vasylieva
Effect of protective coating on the temperature field distribution in the cutting insert at the turning was studied in this paper. The paper also represents the study of wear resistance of cutting tools subjected to the industrial load at the machining. Modelling of the steady state thermal field distribution in the cutting tool was performed by means of 2D finite elements method (FEM). It was established that the main reduction of the cutting temperature in the case of coated cutting insert is due to the reduction of the thermal flow from friction in the contact zone.