In this work, the electrochemical synthesis of PANI and GO-modified PANI was performed using cyclic voltammetry, varying the amount of GO, 1 mg (PG1), 5 mg (PG5), and 10 mg (PG10) to analyze the effect of the amount of GO on the composite. PANI, PG1, PG5, and PG10 materials were characterized using optical microscopy, SEM, UV-vis, FTIR, Raman, and wettability. A stability test was also carried out by putting the materials to 500 oxidation-reduction cycles using cyclic voltammetry. The synthesis method allowed GO in PANI to be added through a chemical interaction between the two compounds. It was also found that the addition of GO led to an improvement in the hydrophilic character of the composite, which would lead to an improvement in the diffusion of reagents/species when the composites are used in aqueous media processes. The results of the stability test showed that the PG10 material presented a lower % loss of specific capacitance and energy compared with the other materials, which indicates that the GO presence (in the amount specified) improves the stability of the PANI. The PG10 material showed favorable and promising conditions for its use in fuel cell and battery processes.
Thin films of monomeric species polythiophene (PTh), poly-(3,4-ethylenedioxythiophene) (PEDOT), and the copolymer PTh/PEDOT were prepared through electropolymerization and deposited above fluorine-doped tin oxide (FTO) substrates. The functional groups of the monomeric species (PTh, PEDOT) and polymeric species (PTh/PEDOT) were characterized by Fourier-transform infrared spectroscopy, while morphological properties were evaluated using scanning electron microscopy, optical microscopy, and atomic force microscopy. The analysis showed that monomers films exhibited less material deposition; otherwise, the copolymer PTh/PEDOT showed better deposition on substrate. In addition, the electrochemical characterization showed that the materials that resulted from copolymerization presented an improvement in electrochemical properties relating to monomer properties. The effect of overoxidation of the monomers applied during the electropolymerization process is also known.
Given the need to improve bioenergy production processes, it is necessary to focus on low-cost culture media and environmental conditions of radiation and temperature. The Scenedesmus dimorphus species was cultured in eutrophicated lagoon water and Bayfolan 0.3% as culture media under four photoperiods with the objective of evaluating the biomass productivity, bioremediation capacity and influence of illumination on the composition and lipid content. It is concluded that the increase of light hours in the culture with eutrophicated lagoon water produces a decrease in the biomass productivity and COD removal percentage. The highest biomass productivity was obtained in photoperiod F1 (10.5:13.5) hours L:O, 0.053 ± 0.0015 g/L day and a removal of 95.6%. Bayfolan 0.3% with F2 (11.5:12.5) and F3 (12.5:11.5) did not show significant differences in the biomass productivity and COD removal. The increase in light hours in the photoperiod induced an increase of 1.01% and 2.84% of saturated fatty acids and 0.8% and 2.14% of monounsaturated fatty acids, as well as a decrease of 3.85% and 2.88% of polyunsaturated fatty acids in eutrophicated lagoon water and Bayfolan 0.3%, respectively.
1 June 2021 in International Journal of Electrochemical Science
Los asfaltenos son mezclas ultracomplejas que impactan negativamente la refinación, producción y transporte del petróleo. El interés en su estudio abarca desde su caracterización para definir su estructura molecular, hasta la comprensión de su comportamiento interfacial. Los asfaltenos presentan una gran diversidad de grupos funcionales y diferentes tipos de asociaciones como las de tipo no covalentes, enlaces de hidrógeno, complejo de coordinación e interacciones entre núcleos aromáticos paralelos. El objetivo de este trabajo fue analizar la composición presente en asfaltenos extraídos de crudos pesados y extrapesados mediante espectroscopía derivada. Se prepararon soluciones de asfaltenos en el rango de concentración de 20 mg/L a 100 mg/L y se analizaron con espectroscopía UV-Vis. La selección de los espectros de orden cero para el procesamiento se realizó con base en la nitidez presente. Los espectros fueron procesados con OriginPro 8.5, para la obtención de espectros derivados de primer y segundo orden. El procesamiento de los espectros de orden cero fue realizado con los filtros Savitsky-Golay y transformada rápida de Fourier (FFT). Los espectros derivados obtenidos presentaron señales nítidas con presencia de poco ruido, lo que hizo posible la identificación de grupos funcionales aromáticos, de 1 a 4 anillos en el rango de longitudes onda de 200 nm a 450 nm. El uso de filtros mejoró la calidad de las señales y permitió la identificación de componentes y estructuras presentes en asfaltenos. El filtro de Savitsky-Golay incrementó la resolución de los espectros derivados de asfaltenos extraídos de crudos pesados y el filtro FFT de asfaltenos de crudos extrapesados. Se observaron diferencias morfológicas entre los asfaltenos extraídos de crudos pesados y extrapesados mediante SEM, que pueden ser relacionadas con la composición y estructuras aromáticas presentes en asfaltenos.