The aim of this study is to analyze the properties of a series of polysaccharide composite films, such as apparent density, color, the presence of functional groups, morphology, and thermal stability, as well as the correlation between them and their antimicrobial and optical properties. Natural antioxidants such as anthocyanins (from cranberry; blueberry and pomegranate); betalains (from beetroot and pitaya); resveratrol (from grape); and thymol and carvacrol (from oregano) were added to the films. Few changes in the position and intensity of the FTIR spectra bands were observed despite the low content of extract added to the films. Due to this fact, the antioxidants were extracted and identified by spectroscopic analysis; and they were also quantified using the Folin-Denis method and a gallic acid calibration curve, which confirmed the presence of natural antioxidants in the films. According to the SEM analysis, the presence of natural antioxidants has no influence on the film morphology because the stretch marks and white points that were observed were related to starch presence. On the other hand, the TGA analysis showed that the type of extract influences the total weight loss. The overall interpretation of the results suggests that the use of natural antioxidants as additives for chitosan-starch film preparation has a prominent impact on most of the critical properties that are decisive in making them suitable for food-packing applications.

Chitosan films were used to remove heavy oil from connate water, deionized water, and seawater. In this research, chitosan–starch films were modified with natural extracts from cranberry, blueberry, beetroot, pomegranate, oregano, pitaya, and grape. These biodegradable, low-cost, eco-friendly materials show an important oil sorption capacity from different water conditions. It was observed that the sorption capacity has a clear correlation with the extract type, quantity, and water pH. In order to understand the physical and chemical properties of the films, they were analyzed according to their apparent density, water content, solubility, and swelling degree by scanning electron microscopy (SEM), thermogravimetric analysis (TGA), gas chromatography–mass spectroscopy (GC–MS), and the determination of surface area using the Brunauer Emmett Teller (BET) method. The results indicate that chitosan–starch films modified with natural extracts can be successfully applied for environmental issues such as oil spill remedy.

In this work, the electrochemical synthesis of PANI and GO-modified PANI was performed using cyclic voltammetry, varying the amount of GO, 1 mg (PG1), 5 mg (PG5), and 10 mg (PG10) to analyze the effect of the amount of GO on the composite. PANI, PG1, PG5, and PG10 materials were characterized using optical microscopy, SEM, UV-vis, FTIR, Raman, and wettability. A stability test was also carried out by putting the materials to 500 oxidation-reduction cycles using cyclic voltammetry. The synthesis method allowed GO in PANI to be added through a chemical interaction between the two compounds. It was also found that the addition of GO led to an improvement in the hydrophilic character of the composite, which would lead to an improvement in the diffusion of reagents/species when the composites are used in aqueous media processes. The results of the stability test showed that the PG10 material presented a lower % loss of specific capacitance and energy compared with the other materials, which indicates that the GO presence (in the amount specified) improves the stability of the PANI. The PG10 material showed favorable and promising conditions for its use in fuel cell and battery processes.

Analysis of crude oil composition provides important information that impacts on the recovery, handling, and transportation of hydrocarbons. Crude characterization also provides data in the analysis of geochemistry of the source of origin. Crude oil characterization by optical methods is usually difficult because of its dark color; however, those characterizations are crucial because they give information that can affect some analysis procedures. Ultraviolet-visible (UV-vis) spectroscopy is a simple and practical technique that allows the characterization of crude oil through dilution in solvents. A comparative study of crude oil solutions contrasted with their asphaltene fractions was performed. Each solution was analyzed in triplicate, on a UV-vis spectrophotometer. Calibration curves for both raw solutions showed no significant variations, indicating stability. Additionally, the results of dispersion and migration phenomena indicated stability only for crude oil solutions. The aggregate size dispersion was different for each type of crude and varied with respect to time. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) showed the type of morphology present for each type of asphaltene.