There are limited studies on the prevalence and incidence of clinically diagnosed hypertrophic myocardiopathy (HCM) and its mortality in the Chinese population, and the projected population burden of HCM over the next decades. We collected data on HCM and its mortality from the Beijing Municipal Health Commission Information Center (BMHCIC) database and estimated the prevalence and incidence based on the whole Beijing population. Calculation of population trends was performed using annual percentage change (APC) and average annual percentage change (AAPC). Finally, future HCM incidence was built by modelling projection of HCM to the next decades using Poisson regression analysis and Gray Model 1,1(GM [1,1]). The prevalence of HCM was 0.0069% (95%CI, 0.0065–0.0072%; N = 1343) in 2010, rising to 0.076% (95% CI, 0.074–0.077%; N = 16,616) in 2019, and the incidence of HCM was 6.85 per 100 000 person-year in 2010, rising to 11.76 per 100 000 person-year in 2019. Males had higher prevalence and incidence of HCM than females. The APPC for the rising incidence of HCM was 5.8% and the expected numbers will double increase in 2029 by assuming the same increase trend as the last decades. HCM had increased annual incidence of HF (APPC: 8.4, 4.4–12.6, p < 0.05), and relatively stable annual incidence of mortality (APPC: 1.2%, − 2.3% to 4.8%, p > 0.05) during the studied period. Males had lower mortality (2.70% vs. 4.20%, p < 0.001) than females. The calculated HCM prevalence was much lower compared to prior screening studies from 2004, although the predicted HCM incidence would double over the next decades. HCM was associated with a stable risk of mortality during the studied period.
Distributed feedback lasers comprised of a reflection section and an active section have been proposed for high direct-modulation bandwidth. The reflection section has the same core layer as the active section so butt-joint re-growth is avoided. Without current injection the reflection section will be pumped to near transparency by the emission from the laser itself so high reflection (> 0.75) can still be achieved as confirmed by the simulation. Therefore a short (150 µm) active section can be used, which enables a low threshold current (~5 mA) and a high direct modulation bandwidth (>30 GHz) as demonstrated by the simulation.
Single-crystal aluminum nitride (AlN) possessing both strong Pockels and Kerr nonlinear optical effects as well as a very large band gap is a fascinating optical platform for integrated nonlinear optics. In this work, fully etched AlN-on-sapphire microresonators with a high-Q of 2.1 × 106 for the TE00 mode are firstly demonstrated with the standard photolithography technique. A near octave-spanning Kerr frequency comb ranging from 1100 to 2150 nm is generated at an on-chip power of 406 mW for the TM00 mode. Due to the high confinement, the TE10 mode also excites a Kerr comb from 1270 to 1850nm at 316 mW. In addition, frequency conversion to visible light is observed during the frequency comb generation. Our work will lead to a large-scale, low-cost, integrated nonlinear platform based on AlN.
We experimentally demonstrated DFB lasers containing an active distributed reflector that has the same waveguide core as the active section. Although without current injection, the distributed reflector will be optically pumped to near transparency by the laser itself, and therefore can provide relatively high reflection to the laser. The laser, fabricated with processing steps similar to standard DFB lasers, has achieved 10-mA threshold current, 0.38-mW/mA slope efficiency, above 55-dB side mode suppression ratio, and 24-GHz modulation bandwidth at 60-mA current injection. 28-Gb/s transmission over 10-km single-mode fibers with a power penalty of less-than 0.5 dB has been demonstrated as well.
16 January 2024 in Journal of Lightwave Technology
Arrayed waveguide grating (AWG) is one of the primary devices of wavelength division multiplexing (WDM) technology with comprehensive advantages of stable performance, high resolution, and a large number of channels. In this work, we demonstrated a low-loss AWG with 100 output channels and a channel spacing of 50 pm based on a z-cut thin-film lithium niobate platform. The length increment of adjacent arrayed waveguides and the etching depth have been optimized to reduce random phase errors. As far as we know, the demonstrated AWG has the largest number of output channels and the smallest channel spacing on the thin-film LiNbO 3 platform.
A novel design of an InP-based monolithic widely tunable laser, multi-channel interference (MCI) laser, is proposed and presented for the first time. The device is comprised of a gain section, a common phase section and a multi-channel interference section. The multi-channel interference section contains a 1x8 splitter based on cascaded 1 × 2 multi-mode interferometers (MMIs) and eight arms with unequal length difference. The rear part of each arm is integrated with a one-port multi-mode interference reflector (MIR). Mode selection of the MCI laser is realized by the constructive interference of the lights reflected back by the eight arms. Through optimizing the arm length difference, a tuning range of more than 40 nm covering the whole C band, a threshold current around 11.5 mA and an side-mode-suppression-ratio (SMSR) up to 48 dB have been predicted for this widely tunable laser. Detailed design principle and numerical simulation results are presented.