In this study, natural Algerian kaolin was used as a support and impregnated with nickel at different loading amounts (2 wt.%, 5 wt.%, and 7 wt.%) in order to prepare a supported catalyst. The wet impregnation technique was used in this preparation; nickel oxide (NiO) was the active phase precursor of the catalyst, and the catalysts were designated as follows: 2%, 5%, and 7% Ni/kaolin. These catalysts were put to the test in catalytic wet peroxide oxidation (CWPO) for degrading the organic contaminant malachite green dye (MG). Analytical techniques such as FTIR spectroscopy, X-ray diffraction, BET, and X-fluorescence were used to examine the structure, morphology, and chemical composition of the support and the produced catalysts. Several parameters, including temperature, catalytic dose, metal loading, hydrogen peroxide volume, and kinetic model were systematically investigated. The combination of improved parameters resulted in a significant increase in the catalytic activity, achieving a high removal rate of MG dye of 98.87%.

The work presented in this paper describes the preparation and the electrochemical application of functionalized chitosan-entrapped carbon paste electrodes (CH/CPE) for lead ions (Pb²⁺) detection in industrial wastewater. The chitosan was first functionalized using TiO₂ and CuO, which were both metal oxides that were obtained by extracting it from waste products derived from shrimp shells. The analytical performance of the as-prepared electrodes, CH/CPE, TiO₂-CH/CPE, and NiO-CH/CPE, for the detection of lead (II) was examined using electrochemical impedance spectroscopy (EIS) technique in the 0.1 M KNO₃ electrolyte solution. The effect of experimental conditions, including polarization potential, frequency, and pH, are optimized to maximize the sensitivity of the measurements. The developed impedimetric sensors provided a linear response over a concentration range of 10⁻⁶ to 10⁻⁴ M with a detection limit of 3.10⁻⁷ M based on S/N = 3. The DFT computational analysis demonstrated that chitosan biopolymer possesses the ability to adsorb Pb (II) ions that are present in wastewater. Chitosan and the derivatives of chitosan, have the potential to remove heavy metals from industrial effluent in a manner that is both economical and eco-friendly to the environment. Chitosan is a biopolymer that is abundantly renewable.

In this investigation, the potential use of native β-cyclodextrin (β-CD) and hydroxypropyl-β-cyclodextrin (HP-β-CD) as encapsulating agents for trichloroethylene (TCE) was assessed. Various quantum chemical parameters, including HOMO, LUMO, and HOMO–LUMO gap, were calculated. The docking process was examined by considering different initial configurations. The complexation energies were calculated at the molecular level using DFT/BLYP-D4 and PBEh-3c calculations to gain insight into TCE encapsulation within the β-CD and HP-β-CD cavities. We used the independent gradient model (IGM) and extended charge decomposition analysis (ECDA) approaches to examine non-covalent interactions and charge transfer within TCE@β-CD and TCE@HP-β-CD complexes. The calculated thermodynamic data and complexation energies exhibited negative values for both considered complexes, indicating a favorable complexation process. Weak Van der Waals intermolecular interactions were the main driving forces in stabilizing the formed complex. Additionally, Monte Carlo simulations were conducted for a better understanding of the inclusion process. Our results provide evidence for the use of β-CD and HP-β-CD as suitable macrocyclic hosts for complexing trichloroethylene.

Due to their detrimental and carcinogenic effects, synthetic organic dyes pose significant environmental and health risks. Consequently, addressing the bioremediation of industrial wastewater containing these organic dyes has become an urgent environmental concern. The adsorption using low-cost and green materials is one of the best alternative techniques for the removal of dyes. This study aims to investigate the use of chitin to eliminate Congo red (CR), an anionic dye, from wastewater. The chitin was produced from shrimp shell in a quick and environmentally friendly manner by utilizing a co-solvent (glycerol/citric acid (GLC)). The resulting adsorbent was characterized through various techniques, including X-ray diffraction (XRD), scanning electron microscopy (SEM), and FT-IR spectroscopy. The effectiveness of CR removal with chitin was studied with respect to contact time, adsorbent dose, initial pH, equilibrium isotherms, and kinetic and thermodynamic parameters. It was observed that variations in the dye concentration and pH significantly influenced the removal of CR with chitin. Under optimal operating conditions (pH = 7, contact time = 130 min, temperature = 50 °C), the adsorption capacity reached 29.69 ± 0.2 mg/g. The experimental data revealed that CR adsorption onto a chitin adsorbent is better represented by a Langmuir isotherm.