Roman Čička

Dr. Roman Čička

orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 September 2025 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
IČIvona Černičková
Ivona Černičková
LĎLibor Ďuriška
Libor Ďuriška
MDMarian Drienovsky
Marian Drienovsky
YPYuriy Plevachuk
Yuriy Plevachuk
PŠPeter Švec
Peter Švec
RČRoman Čička
Roman Čička

22 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
AOAndrej Opálek
Andrej Opálek
ŠEŠtefan Emmer
Štefan Emmer
RČRoman Čička
Roman Čička
NBNaďa Beronská
Naďa Beronská
POPeter Oslanec
Peter Oslanec
Jaroslav KovacikJaroslav Kovacik
Jaroslav Kovacik
Copper–graphite composites are promising functional materials exhibiting application potential in electrical equipment and heat exchangers, due to their lower expansion coefficient and high electrical and thermal conductivities. Here, copper–graphite composites with 10–90 vol. % graphite were prepared by hot isostatic pressing, and their microstructure and coefficient of thermal expansion (CTE) were experimentally examined. The CTE decreased with increasing graphite volume fraction, from 17.8 × 10−6 K−1 for HIPed pure copper to 4.9 × 10−6 K−1 for 90 vol. % graphite. In the HIPed pure copper, the presence of cuprous oxide was detected by SEM-EDS. In contrast, Cu–graphite composites contained only a very small amount of oxygen (OHN analysis). There was only one exception, the composite with 90 vol. % graphite contained around 1.8 wt. % water absorbed inside the structure. The internal stresses in the composites were released during the first heating cycle of the CTE measurement. The permanent prolongation and shape of CTE curves were strongly affected by composition. After the release of internal stresses, the CTE curves of composites did not change any further. Finally, the modified Schapery model, including anisotropy and the clustering of graphite, was used to model the dependence of CTE on graphite volume fraction. Modeling suggested that the clustering of graphite via van der Waals bonds (out of hexagonal plane) is the most critical parameter and significantly affects the microstructure and CTE of the Cu–graphite composites when more than 30 vol. % graphite is present.

1 January 2025 in Applied Engineering Letters : Journal of Engineering and Applied Sciences
Verified
Journal Article
Open access
TMTereza Machajdíková
Tereza Machajdíková
RČRoman Čička
Roman Čička
IČIvona Černičková
Ivona Černičková
LĎLibor Ďuriška
Libor Ďuriška
MDMarian Drienovsky
Marian Drienovsky
JPJakub Perička
Jakub Perička
This study investigates the addition of Ni into SAC305 solder alloy with varying nickel content (0–4 wt.% Ni) using experimental techniques and computational thermodynamics. The experimental part employed various techniques (scanning electron microscopy, X-ray diffraction, energy-dispersive X-ray spectroscopy, and differential scanning calorimetry). The microstructure of the investigated alloys consisted of primary β-Sn and an eutectic mixture containing β-Sn and two intermetallic compound particles (Ag3Sn and Cu6Sn5). Small Ni additions (up to 0.2 wt.%) refined the microstructure and significantly reduced the undercooling from 30°C (SAC305) to about 12°C. However, Ni additions exceeding 0.4 wt.% led to microstructural coarsening and formation of Ni3Sn4 phase. For the computational part, Thermo-Calc software was used to investigate the conditions of Cu6Sn5 and Ni3Sn4 phase formation. The experimental results were consistent with computations from Thermo-Calc. The results suggest that minor Ni additions (up to 0.2 wt.%) offer possibilities to refine the microstructure and reduce undercooling, potentially improving the properties of solders.

10 December 2025 in Journal of Physical Studies
Verified
Journal Article
Closed access
PDPatrícia Danišovičová
Patrícia Danišovičová
MDMarian Drienovsky
Marian Drienovsky
LĎLibor Ďuriška
Libor Ďuriška
RČRoman Čička
Roman Čička
TMT. Machajdíková
T. Machajdíková
IČIvona Černičková
Ivona Černičková

1 January 2021
Verified
Conference Paper
Open access
LRLukáš Rausa
Lukáš Rausa
JĎJuraj Ďurica
Juraj Ďurica
MMMaros Martinkovic
Maros Martinkovic
RČRoman Čička
Roman Čička
MPMatej Pašák
Matej Pašák
Peter JurčiPeter Jurči
Peter Jurči

1 September 2018 in Research Papers Faculty of Materials Science and Technology Slovak University of Technology
Verified
Journal Article
Open access
PDF file
MDMarian Drienovsky
Marian Drienovsky
LTLýdia Rízeková Trnková
Lýdia Rízeková Trnková
RČRoman Čička
Roman Čička
PPPavol Priputen
Pavol Priputen
MPMarcela Pekarcikova
Marcela Pekarcikova
JJJozef Janovec
Jozef Janovec
The influence of increased Cu and Ag contents on the microstructure evolution in the utilized Sn-0.3Ag-0.7Cu (wt. %) solder was studied. The utilized solder was exploited in the wave soldering process at the temperatures of about 260 °C for several days. The samples investigation involved the differential scanning calorimetry, the scanning electron microscopy including the energy dispersive X-ray spectroscopy, and the X-ray diffraction techniques. To predict phase equilibria at various temperatures and temperature dependences of heat capacity, the Thermo-Calc software and the COST531 lead-free solder database were used. The original and the utilized solders were found to be very similar regarding the phase occurrence, but slightly differ from one another in microstructure evolution due to higher bulk contents of Cu in the latter solder. The obtained results contribute to both the better understanding of the microstructure evolution in low-silver Sn-Ag-Cu solders and the determination of compositional limits for those solders used in the wave soldering process.