We present two different designs of robust, easily manufactured metamaterial-based films of subwavelength thickness capable of full absorption of incident terahertz radiation at certain frequencies. Both designs allow a choice between the total absorption of all polarizations or only one linear polarization while the other polarization is reflected. Even if the films are optimized for normal incidence, the absorption remains greater than 99% for angles up to in the TE and up to in the TM case. In the first design, the maximum absorption frequency shifts considerably with angle, and in the second design it is independent of angle.
1 September 2016 in Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment
We present the detailed description of the successful design and cold test of photonic band gap (PBG) resonators and traveling-wave accelerator structures. Those tests provided the essential basis for later hot test demonstration of the first PBG accelerator structure at 17.140 GHz [E. I. Smirnova, A. S. Kesar, I. Mastovsky, M. A. Shapiro, and R. J. Temkin, Phys. Rev. Lett., 95, 074801 (2005).]. The advantage of PBG resonators is that they were built to support only the main, -like, accelerator mode while not confining the higher-order modes (HOM) or wakefields. The design of the PBG resonators was based on a triangular lattice of rods, with a missing rod at the center. Following theoretical analysis, the rod radius divided by the rod spacing was held to a value of about 0.15 to avoid supporting HOM. For a single-cell test the PBG structure was fabricated in X-band (11 GHz) and brazed. The mode spectrum and factor () agreed well with theory. Excellent HOM suppression was evident from the cold test. A six-cell copper PBG accelerator traveling-wave structure with reduced long-range wakefields was designed and was built by electroforming at Ku-band (17.140 GHz). The structure was tuned by etching the rods. Cold test of the structure yielded excellent agreement with the theoretical design. Successful results of the hot test of the structure demonstrating the acceleration of the electron beam were published in E. I. Smirnova, A. S. Kesar, I. Mastovsky, M. A. Shapiro, and R. J. Temkin, Phys. Rev. Lett., 95, 074801 (2005).
10 June 2008 in IEEE Transactions on Plasma Science
We have designed, fabricated, and tested with low power a novel W-band traveling-wave tube (TWT) structure based on a slow-wave cylindrically symmetric photonic band gap (PBG) structure, or an ldquoomniguide.rdquo The development of wideband millimeter-wave power amplifiers is underway at Los Alamos National Laboratory. PBG TWT structures have great potential for very large bandwidth and linear dispersion. In addition, being cheap to fabricate, the PBG structures enhance commercial transferability of W-band TWT technology. The omniguide structure was designed and fabricated with silica dielectric with a copper harness. Cold-test results were found to be in excellent agreement with the design. A bandwidth of more than 10% was demonstrated. This structure is designed to generate millimeter-wave RF when driven by a 2-A 120-keV electron beam.
We report the high gradient testing results of two single-cell off-axis coupled standing wave accelerating structures. Two brazed standing wave off-axis coupled structures with the same geometry were tested: one made of pure copper (Cu) and one made of a copper–silver (CuAg) alloy with a silver concentration of 0.08%. A peak surface electric field of 450 MV/m was achieved in the CuAg structure for a klystron input power of 14.5 MW and a 1 μs pulse length, which was 25% higher than the peak surface electric field achieved in the Cu structure. The superb high gradient performance was achieved because of the two major optimizations in the cavity's geometry: (1) the shunt impedance of the cavity was maximized for a peak surface electric field to accelerating gradient ratio of ∼2 for a fully relativistic particle, and (2) the peak magnetic field enhancement due to the input coupler was minimized to limit pulse heating. These tests allow us to conclude that C-band accelerating structures can operate at peak fields similar to those at higher frequencies while providing a larger beam iris for improved beam transport.
28 April 2014 in Physical Review Special Topics - Accelerators and Beams
Recently, considerable attention has been focused on electron beam current profile shaping by means of a transverse beam mask followed by an emittance exchanger (EEX). This setup can transform a transverse particle distribution into a longitudinal particle distribution. We investigate the EEX technique with application to production of a double triangular drive and a trapezoidal main bunches for high transformer ratio, high brightness dielectric wakefield accelerators. We perform numerical optimization of two realistic configurations: a double dogleg and a chicane. In this paper we report sample designs and discuss the effects of the beam line nonlinearities, beam space charge, and coherent synchrotron radiation on a current profile of the output beam.