To investigate the unclamped inductive switch (UIS) characteristics, 1200 V silicon carbide (SiC) planar MOSFETs with four cell topologies of linear, current sharing linear, square, and hexagon are designed and manufactured. The experimental platform was built and tested. The results show that the single pulse avalanche energy density of the linear cell topology is 1.69 times higher than that of the square and 1.49 times that of the hexagon. Further, the UIS process is simulated by using physical simulation, which shows that the avalanche energy was concentrated near the corner of the P-base region in the UIS mode. From this, the avalanche energy distribution differences of the four cell topologies were analyzed and compared. A theoretical model of avalanche heating per unit area is proposed, which shows that the avalanche energy density is inversely proportional to the proportion of avalanche energy concentration region. This study may contribute to the cell topology design of SiC MOSFETs under the application scenario with high avalanche reliability requirements.
8 January 2025 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper compares and evaluates the single pulse short-circuit robustness of SiC MOSFETs with linear and hexagonal cell topologies under different gate voltages, bus voltages, and case temperatures. The short-circuit failure mechanisms of the linear and hexagonal cell topologies are studied. A new switching model for gate failure and thermal runaway short-circuit failure modes is proposed and analyzed. The robustness performance of the linear and hexagonal cell topologies is compared and evaluated under the same short-circuit power for the first time, fully revealing the comprehensive impact mechanism of cell topologies on the short-circuit robustness for SiC MOSFETs.
16 April 2024 in IEEE Transactions on Device and Materials Reliability
The hexagonal cell topology of planar SiC VDMOSFETs with varied JFET width (LJFET) are designed and manufactured in this study. LJFET = 1.4μm has the best HF-FOM (Ron×Cgd) and HF-FOM (Ron×Qgd) by comparing the dynamic and static parameters of each design. Besides, the UIS reliability and failure mechanism for series designs are investigated by experiment and TCAD simulation. The results show that the high temperature is generated by energy dissipation during avalanche and it drives the parasitic BJT conduction, causing Ids out of control and instantaneous heat concentration in a very short time. The extremely high temperature causes internal cracking of the material and metal melting, resulting in gate-source short circuit and device damage. It would provide suggestions for device design and reliability consideration.
A novel 4H-SiC Multiple Stepped SGT MOSFET (MSGT-MOSFET) is presented and investigated utilizing TCAD simulations in this paper. We have quantitatively studied the characteristics of the device through simulation modeling and physical model calculations, and comparatively analyzed the performance and application prospects of this novel device. The gate-to-drain capacitance (Cgd) and gate-to-drain charge (Qgd) of the MSGT-MOSFET are significantly reduced in comparison with the double trench MOSFET (DT-MOSFET) and the conventional SGT MOSFET (CSGT-MOSFET), due to the reduction of the overlapping area of the split gate (SG) structure and drift region. Therefore, the obtained high frequency figure of merit (HF-FOM) defined as [Ron × Cgd] reduced by 23.9% compared with DT-MOSFET and CSGT-MOSFET. And the HF-FOM [Ron × Qgd] for the MSGT-MOSFET significantly decreased by 71% and 50%, respectively, compared to that of the DT-MOSFET and CSGT-MOSFET. Furthermore, the switching loss is also simulated and calculated. And the total switching loss of the proposed MSGT-MOSFET realizes 42.9% and 21.7% reduction in comparison with the DT-MOSFET and CSGT-MOSFET. The overall enhanced performances suggest that the MSGT-MOSFET is an excellent choice for high frequency power electronic applications.
The reliability and failure mechanism of SiC MOSFET under short-circuit was investigated using experiment and physical simulation in this paper. A short-circuit test platform was constructed, and a physical simulated model was calibrated. A commercial 1.2kV SiC MOSFET operated under different voltages including 200V, 400V, 600V with series short-circuit time was studied. The results showed that the thermal dissipation played a critical role during short-circuit operation, which is one of the most impacting factor to gate voltage and current tails. Two failed mechanisms including gate oxide degradation and parasitic BJT conduction failure were verified during short-circuit. This study may be helpful to the application engineering of SiC MOSFET.
9 April 2025 in Materials Science in Semiconductor Processing