Using TCAD simulations, the silicon carbide metal-oxide-semiconductor field-effect transistor with p-type floating islands (SiC FLIMOSFET) is systematically investigated in this paper. The doping concentration (NFLI), length (L), and position (D1) of floating islands are optimized according to breakdown voltage (BV), electric field distribution, and on-resistance. The results show that NFLI = 1 x 10¹⁷ cm⁻³, L= 2.5 μm, and D1=9.0 μm are superior values for FLI structure considering tradeoff between BV and on-resistance. With the same BV capacity, the on-resistance of SiC FLIMOSFET is decrease by 32% comparing to the conventional SiC VDMOSFET. Besides, the dynamic property shows 16.5% reduction of FoM Ron· QGD in the SiC FLIMOSFET. Significantly, comparing to the conventional structure, the electro-thermal simulation indicates that the SiC FLIMOSFET has a higher robustness under short-circuit condition owing to the reduction of thermal stress in SiC/SiO₂ interface. All the results show that the SiC FLIMOSFET has a good potential in SiC power device.
6 January 2023 in IEEE Transactions on Electron Devices
To investigate the unclamped inductive switch (UIS) characteristics, 1200 V silicon carbide (SiC) planar MOSFETs with four cell topologies of linear, current sharing linear, square, and hexagon are designed and manufactured. The experimental platform was built and tested. The results show that the single pulse avalanche energy density of the linear cell topology is 1.69 times higher than that of the square and 1.49 times that of the hexagon. Further, the UIS process is simulated by using physical simulation, which shows that the avalanche energy was concentrated near the corner of the P-base region in the UIS mode. From this, the avalanche energy distribution differences of the four cell topologies were analyzed and compared. A theoretical model of avalanche heating per unit area is proposed, which shows that the avalanche energy density is inversely proportional to the proportion of avalanche energy concentration region. This study may contribute to the cell topology design of SiC MOSFETs under the application scenario with high avalanche reliability requirements.
16 April 2024 in IEEE Transactions on Device and Materials Reliability
The hexagonal cell topology of planar SiC VDMOSFETs with varied JFET width (LJFET) are designed and manufactured in this study. LJFET = 1.4μm has the best HF-FOM (Ron×Cgd) and HF-FOM (Ron×Qgd) by comparing the dynamic and static parameters of each design. Besides, the UIS reliability and failure mechanism for series designs are investigated by experiment and TCAD simulation. The results show that the high temperature is generated by energy dissipation during avalanche and it drives the parasitic BJT conduction, causing Ids out of control and instantaneous heat concentration in a very short time. The extremely high temperature causes internal cracking of the material and metal melting, resulting in gate-source short circuit and device damage. It would provide suggestions for device design and reliability consideration.
The reliability and failure mechanism of SiC MOSFET under short-circuit was investigated using experiment and physical simulation in this paper. A short-circuit test platform was constructed, and a physical simulated model was calibrated. A commercial 1.2kV SiC MOSFET operated under different voltages including 200V, 400V, 600V with series short-circuit time was studied. The results showed that the thermal dissipation played a critical role during short-circuit operation, which is one of the most impacting factor to gate voltage and current tails. Two failed mechanisms including gate oxide degradation and parasitic BJT conduction failure were verified during short-circuit. This study may be helpful to the application engineering of SiC MOSFET.
Silicon carbide (SiC) is presenting as an attractive material for the next generation high voltage power devices which benefits from its excellent material properties. SiC Schottky barrier diode (SBD) compares with silicon based, which has superior characteristics in terms of rectification, reverse recovery time, etc. In this paper, a high voltage 4H-SiC SBD with reverse breakdown voltage of 1800 V and forward current of 40 A is designed as implemented in TCAD. The termination structure of the device is designed with multiple Field Limiting Rings (FLRs). The parameters of the active area and FLRs terminal protection structure are optimized. The steady state and transient characteristics of the device are simulated separately. As a result, the thickness of the N-type epitaxial layer is 16 μm and the doping concentration is 5.8×10 15 cm -3 . Furthermore, the forward current is 40 A when the forward voltage is 1.60 V at room temperature. Finally, a temperature generation model is added to calculate the lattice temperature profile and analysis areas of possible failure during pulsed operation.
21 April 2025 in IEEE Transactions on Device and Materials Reliability
Field-Stop Insulated Gate Bipolar Transistors (FS-IGBTs) are widely used in various power applications due to their low conduction and switching losses. However, further reductions in cell pitch lead to increased cell density, resulting in higher saturation current that adversely impacts the short-circuit ruggedness essential for applications such as welding machines and motor drives. This paper details the design and fabrication of a 650V, 75A FS-IGBT. By incorporating dummy gate and emitter trench structures within the active gate and optimizing the layout of the three cell structures, the short-circuit characteristics of the device are markedly improved. Experimental tests confirm that the device exhibits both low saturation on-state voltage and short-circuit ruggedness. This study further investigates the circuit parameters related to short-circuit conditions and comprehensively analyzes the impact of each parameter on the short-circuit characteristics of the FS-IGBT. The experimental results indicate that the bus voltage VDC, gate voltage VG, and temperature TC significantly influence the short-circuit performance of the FS-IGBT. Therefore, a moderate decrease in VDC, VG, and TC can effectively enhance the short-circuit ruggedness and the short-circuit withstand time tSC of the device.