Hot-rolled backup rolls are widely used in steel rolling and usually need to be repaired by arc hardfacing after becoming worn. However, a corrugated-groove defect commonly occurs on the roll surface due to the uneven hardness distribution in the hardfacing layers, affecting the proper usage of the roll. Accordingly, a new swing-arc submerged arc welding (SA-SAW) process is proposed to attempt to solve this drawback. The microstructure and hardness are then investigated experimentally for both SAW and SA-SAW hardfacing layers. It is revealed that a self-tempering effect occurs in the welding pass bottom and the welding pass side neighboring the former pass for both processes, refining the grain in the two areas. In all the zones, including the self-tempering zone (STZ), heat-affected zone (HAZ), and not-heat-affected zone in the welding pass, both SAW and SA-SAW passes crystallize in a type of columnar grain, where the grains are the finest in STZ and the coarsest in HAZ. In addition, the arc swing improves the microstructure homogeneity of the hardfacing layers by obviously lowering the tempering degree in HAZ while promoting the even distribution of the arc heat. Accordingly, the hardness of the SA-SAW bead overall increases and distributes more uniformly with a maximum difference of < 80 HV_0.5 along the horizontal direction of the bead. This hardness difference in SA-SAW is accordingly decreased by ~38.5% compared to that of the SAW bead, further indicating the practicability of the new process.

A new brazing process for thin-walled stainless steel was proposed by combining green and efficient Ni-Cr-P electrodeposition with brazing technology. Novel information was attained by analyzing the electrodeposited Ni-Cr-P interlayers and the brazed joints and characterizing them using a combination of advanced techniques. The incorporation mechanisms of impurities (i.e., oxygen and carbon) in the Ni-Cr-P interlayers electrodeposited from a Cr(III)–glycine solution were revealed. The oxygen mainly came from the Cr(III)–hydroxy complexes formed by the hydrolysis and olation between Cr(III) complexes and OH⁻ ions near the cathode. Glycine did not directly participate in the cathode reactions but decomposed on the anode surface. These byproducts (carbonyl compounds) were directly incorporated into the interlayers in a molecular pattern, forming a weak link to the metallic chromium. Brazing test results showed that a certain amount of Cr₂O₃ powder, formed by the decomposition of chromium hydroxides in the interlayers under high-temperature catalysis, would cause the degradation of the brazed joints. Using the step-wise brazing method, the brazing sheets were first annealed to eliminate the impurities by utilizing the strong reducing effect of hydrogen and the weak link characteristics between carbonyl compounds and metallic chromium atoms. An excellent joint with a shear strength of 63.0 MPa was obtained by subsequent brazing. The microstructural analysis showed that the brazed seam was mainly composed of a Ni-Fe-Cr solid solution, the Ni₃P eutectic phase, and small quantities of the Ni₅P₂ phase scattered in the Ni₃P eutectic phase. Fracture mode observations showed that the cracks extended along the interface between the brittle P-containing phase and the primary phase, resulting in fracture.

To raise narrow gap GMA welding efficiency while ensuring weld formation, the present work presents a thick wire swing arc narrow gap GMA welding process assisted by cold wires. This process employs the thick wire and the pre-embedded cold wires to jointly increase the welding efficiency, while improving the groove sidewall penetration by the swing arc. Two types of thick wires, being conventional single-strand welding wire (SWW) and cable-type welding wire (CWW), are respectively used as main wire. After solving the series arc problem during CWW arc-igniting, the effects of the pre-embedded wire layer number on narrow gap weld formation and welding efficiency are investigated for the thick wire welding. Experimental results show that the weld thickness and the sidewall penetration do not obviously change with increasing the number of the cold wires, while the weld layer height significantly grows. Additionally, the SWW weld formation looks more sound. Compared to the thin-wire welding, the thick wire welding without the cold wire raises the deposition rate by about 38% and 58% as respectively using SWW and CWW. When pre-embedding two layers of cold wires, the increased percentage of the deposition rate further rises respectively to about 81% and 112%. These thus demonstrate the effectiveness of the developed process in addition to the higher efficiency of the CWW welding.