Microalgae have been shown to be a source of multiple bio-based products ranging from high value molecules to commodities. Along with their potential to produce a large variety of products, microalgae can also be used for the depollution of wastewaters of different origins (urban, industrial, and agricultural). This paper is focused on the importance of harnessing the bioremediation capacity of microalgae to treat wastewaters in order to develop the microalgae industry (especially the microalgae biofuel industry) and to find other alternatives to the classic wastewater treatment processes. The current research on the potential of microalgae to treat a specific wastewater or a targeted pollutant is reviewed and discussed. Then, both strategies of selecting the best microalgae strain to treat a specific wastewater or pollutant and using a natural or an artificial consortium to perform the treatment will be detailed. The process options for treating wastewaters using microalgae will be discussed up to the final valorization of the biomass. The last part is dedicated to the challenges which research need to address in order to develop the potential of microalgae to treat wastewaters.
Arthrospira platensis (Spirulina) is the most cultivated microalga worldwide. Improving its cultivation in terms of biomass productivity, quality, or production cost could significantly impact the Spirulina industry. The objectives of this paper were defined as to contribute to this goal. Spirulina biomass productivity was investigated through medium choice. A modified Zarrouk’s medium was selected as it gave higher final dry weights and longer sustained growth than Hiri’s and Jourdan’s media. Then, in order to reduce Spirulina production cost, modified Zarrouk’s medium was rationalized by testing different dilutions. It was found that modified Zarrouk’s medium could be diluted up to five times without impacting the growth rates in a 28-days batch cultivation. Higher dry weights were even observed after 21 days of batch cultivation (1.21 g/L for 20%-modified Zarrouk’s medium in comparison to 0.84 g/L for modified Zarrouk’s medium). Iron uptake was then investigated as one of the major contributors to Spirulina nutritional quality. An increase in iron content was obtained by replacing iron sulfate by iron EDTA at a concentration of 10 mgFe/L (2.11 ± 0.13 mgFe/gbiomass for EDTA-FeNa, 3 H2O at 10 mgFe/L compared to 0.18 ± 0.13 for FeSO4,6H2O at 2 mgFe/L). Impact of light intensity on Spirulina biomass productivity was also investigated in a 2 L Photobioreactor (PBR). Specific growth rates were calculated for Photosynthetically Photon Flux Densities (PPFD) from 85 to 430 µmol/m2/s. At 430 µmol/m2/s, photoinhibition was not observed and the specific growth rate was maximum (0.12/day). Finally, a 40-day cultivation experiment was conducted in a 1000 L PBR giving a maximum daily areal productivity of 58.4 g/m2/day. A techno-economic analysis gave production cost two to 20 times higher for PBR (from 18.71 to 74.29 €/kg) than for open ponds (from 3.86 to 9.59 €/kg) depending on Spirulina productivity.
Hydroponic farms produce wastewater that need to be treated before being released into the environment. A three-step screening process (microplate, batch, and semi-continuous flasks experiments) initially designed to select an efficient microalgae strain allowed the isolation of a consortium that naturally developed in the hydroponic farm wastewater. During the non-optimized semi-continuous experiments, the best performing microalgae strain, Scenedesmus obliquus UTEX393 and the wastewater-born consortium cultures achieved good average linear growth rate (0.186 and 0.198/d, respectively) and high average nitrogen removal rates (23.5 mgN/L/d and 21.9 mgN/L/d, respectively). Phosphorus removal was very high probably due to precipitation. An integrated process was designed to treat the hydroponic farm wastewater using the wastewater-born consortium. Despite relatively low coagulation efficiencies in the preliminary tests, when integrated in a continuous process, chitosan was efficient to harvest the naturally wastewater-born consortium. The process was also efficient for removing nitrate and phosphate in less than seven days (average removal of 98.2 and 87.1% for nitrate and phosphate, respectively). These very promising results will help to define a pre-industrial pilot process.
20 September 2007 in Sensors and Actuators B: Chemical
Microalgae, particularly Chlorella vulgaris, are promising sustainable sources of starch for bioplastics and biofuels. Economically viable production requires optimizing starch accumulation, typically triggered by nutrient starvation, a process often facilitated by culture dilution to enhance light homogeneity. This study proposes an empirical model to predict the optimal cell concentration for starch accumulation under nitrogen starvation based on available light. The model, developed using 1-L outdoor cultures, was successfully applied to a 180-L photobioreactor. The theoretical optimal concentration under 330 µmolphotons m-2 s-1 (average absorbed photon flux density during daylight) was found at 0.8 gDWL-1. The corresponding carbohydrate productivity (43 mgcarbohydrate L-1 h-1 during daylight), carbohydrate content (57 %) and photosynthesis efficiency (6.8 % expressed as kJcarbohydrate kJphotonsPAR-1) aligned with experimental results. This study indicates that optimal carbohydrate accumulation occurs at low cell concentration, which is a critical guideline for the future industrialization of microalgae production.
Microalgae are emerging as a promising feedstock for bioplastics, with Chlorella vulgaris yielding significant amounts of starch. This polysaccharide is convertible into thermoplastic starch (TPS), a biodegradable plastic of industrial relevance. In this study, we developed a pilot-scale protocol for extracting and purifying starch from starch-enriched Chlorella vulgaris biomass. From 430.3 ± 0.5 g (dry weight - DW) of microalgae biomass containing 42.2 ± 3.4 % of starch, we successfully extracted 205.8 ± 1.2 g DW of purified starch extract containing 86.9 ± 3.0 % of starch, resulting in a final recovery yield of 98.5%. We have characterized this extracted starch and processed it into TPS using twin-screw extrusion and injection molding. Microalgal starch showed similar properties to those of native plant starch, but with smaller granules. We compared the mechanical properties of microalgal TPS with two controls, namely a commercial TPS and a TPS prepared from commercial potato starch granules. TPS prepared from microalgal starch showed a softer and more ductile behavior compared to the reference materials. This study demonstrates the feasibility of recovering high-purity microalgal starch on a pilot scale with high yields, and highlights the potential of microalgal starch for the production of TPS using industrially relevant processes. Graphical