Vanadium dioxide (VO2) has attracted interest due to its phase transition from the insulating to the metallic states for potential use in a variety of optical and photonic applications. Here, we propose a VO2/Si core-shell structure to improve switching in band-selective reflection properties of the composite. Mie scattering formulation is used to analyze the structure before and after phase transition to show the impact of resonance quality on the mid-infrared light back-scattering. After investigating the effect of various VO2 nano-sphere radius sizes in both phases on light reflectivity, a VO2/Si core-shell structure is proposed to boost reflectivity and improve light controllability. Randomly distributed nanoparticles are studied to illustrate how these composites have similar behavior to their deterministic-distributed counterpart. Our results indicate that up to two-thirds of incident light power can be controlled by embedding proper core-shells in a polymer host material.
20 November 2025 in Energy Conversion and Management
Sensors fabricated by using a silicon-on-insulator (SOI) platform provide promising solutions to issues such as size, power consumption, wavelength-specific nature of end reflectors and difficulty to detect ternary mixture. To address these limitations, we proposed and investigated a broadband-thermally tunable vanadium dioxide (VO2)-based linear optical cavity sensor model using a finite element method. The proposed structure consists of a silicon wire waveguide on a silicon-on-insulator (SOI) platform terminated with phase-change vanadium oxide (VO2) on each side to provide light confinement. A smooth transmission modulation range of 0.8 (VO2 in the insulator state) and 0.03 (VO2 in the conductive phase state) in the 125 to 230 THz spectral region was obtained due to the of Fabry–Pérot (FP) effect. For the 3.84 μm cavity length, the presented sensor resulted in a sensitivity of 20.2 THz/RIU or 179.56 nm/RIU, which is approximately two orders of magnitude higher than its counterparts in the literature. The sensitivity of the 2D model showed direct relation with the length of the optical cavity. Moreover, the change in the resonating mode line width of approximately 6.94 THz/RIU or 59.96 nm/RIU was also observed when the sensor was subjected to the change of the imaginary part k of complex refractive index (RI). This property of the sensor equips it for the sensing of aternary mixture without using any chemical surface modification. The proposed sensor haspotential applications in the areas of chemical industries, environmental monitoring and biomedical sensing.
24 January 2024 in Journal of the Optical Society of America B
Refractory metals, which include niobium, tantalum, molybdenum, and tungsten, are critical components in applications in extreme environments due to their attractive thermomechanical properties. However, their low reflectivity below 1500 nm has prompted researchers to focus on increasing their reflection at shorter wavelengths. In this study, we applied an adjoint-based optimization technique to improve the spectral reflectivity of refractory metals in the broadband spectrum (300–3000 nm). An optimized periodic multilayer consisting of SiO2/TiO2 is selected as a starting point for the process. Then, the adjoint-based method is implemented to enhance the reflection of the surfaces. This approach involves an iterative procedure that guarantees improvement in every iteration. In every iteration, both the direct and adjoint solutions of Maxwell’s equations are computed to predict the scattering characteristics of a particular microstructure on a surface and measure its effectiveness. The results of our study indicate that the final designs not only increase reflectivity to over 90% but also have thermomechanical benefits that make them suitable for use in harsh environments. We also explored the effect of initial geometry on the results. Overall, our study shows that the adjoint-based optimization technique is an effective method for creating high-performing broadband reflectors with refractory metal substrates coated with dielectric multilayers.
We experimentally investigate how shear-thinning rheology modifies the near-wall motion of low-Reynolds-number propellers. Using a magnetic actuation platform, we examine two representative systems: a rotating spherical roller and a helical propeller near a solid boundary. In a Newtonian fluid, the spherical roller exhibits forward wall-induced translation, while the helical propeller displays forward propulsion accompanied by lateral drift. In shear-thinning fluids, however, increasing the actuation frequency qualitatively alters these behaviors. For the spherical roller, the direction of wall-induced translation reverses beyond a critical frequency, producing backward motion. For the helical propeller, shear-thinning rheology reverses the lateral drift while simultaneously enhancing forward propulsion. These results provide direct experimental evidence that shear rate-dependent viscosity can fundamentally modify boundary-mediated propulsion at low Reynolds number, with implications for the design and control of microrobots operating in complex biological fluids.