In this paper, a virtual temporal phase-shifting method based on generative adversarial networks (GANs) is proposed to realize dynamic measurement, which is referred to as PSNet. The proposed PSNet can produce the virtual phase-shifting fringe patterns from the single-frame fringe pattern, and the standard n -step phase-shifting method is employed to obtain the wrapped phase from the virtual fringe patterns. The wrapped phase can further be unwrapped by the unwrapping algorithm. Simulation analysis shows that the PSNet can produce the virtual phase-shifting fringe patterns without noise, and thus, the denoising process is eliminated. The performance of the method is verified from the captured fringe in the interferometer, which demonstrates the practicability of the proposed method.

The use of zinc (Zn) alloys as a biodegradable metal for medical purposes has been a popular research topic. This study investigated the strengthening mechanism of Zn alloys to enhance their mechanical properties. Three Zn-0.45Li (wt.%) alloys with different deformation amounts were prepared by rotary forging deformation. Their mechanical properties and microstructures were tested. A simultaneous increase in strength and ductility was observed in the Zn-0.45Li alloys. Grain refinement occurred when the rotary forging deformation reached 75.7%. The surface average grain size reached 1.19 ± 0.31 μm, and the grain size was uniformly distributed. Meanwhile, the maximum elongation of the deformed Zn-0.45Li was 139.2 ± 18.6%, and the ultimate tensile strength reached 426.1 ± 4.7 MPa. In situ tensile tests showed that the reinforced alloys still broke from the grain boundary. Continuous and discontinuous dynamic recrystallization during severe plastic deformation produced many recrystallized grains. During deformation, the dislocation density of the alloy first increased and then decreased, and the texture strength of the (0001) direction increased with deformation. Analysis of the mechanism of alloy strengthening showed that the strength and plasticity enhancement of Zn-Li alloys after macro deformation was a combination of dislocation strengthening, weave strengthening, and grain refinement rather than only fine-grain strengthening as observed in conventional macro-deformed Zn alloys.

The metallization of polyetherimide (PEI) is widely considered to enhance its surface properties and enhance its application in engineering fields; however, adhesion is a key factor in determining the reliability of PEI metallization. A Ni/Cu/Ni multilayer coating was successfully manufactured on a batch of PEI resin reinforced with glass fibers by a two-step metallization process, including sandblasting and activation/acceleration. The microstructure and morphology of the top-surface and cross-section of the coatings were observed by scanning electron microscopy. The chemical state and composition of the deposits were characterized by both X-ray photoelectron and energy-dispersive spectroscopy. The adhesion state was qualitatively evaluated by cross-cut tests with 3M tape. The surface roughness of the substrate significantly increased after the sandblasting process, which could improve the adhesion between the multilayer coating and the PEI substrate. After the standard activation process, the acceleration made an effect on the deposition of the initial Ni layer for electroless plating. The influence of acceleration on the appearance quality of metallization on the PEI substrate was studied and, at the same time, the mechanism of acceleration was investigated and addressed.

At the initial rolling temperature of 400 °C, ZK60 magnesium alloy was hot rolled by three different rolling paths with different roll speed ratios (RSR) of 1:1.15, 1:1.2, and 1:1.5, respectively. The effects of different rolling processes on the microstructure and mechanical properties of the alloy were studied. The microstructure, plasticity, strength, hardness, and texture intensity of rolled samples were analyzed in this work. The results show that the microstructure uniformity of the alloy under multi-path asynchronous rolling (MAR) is significantly improved, which improves the mechanical properties of the material to a certain extent, and effectively weakens the texture intensity of the basal plane and reduces the anisotropy. The amount of randomly oriented grains of ZK60 magnesium alloy rolled by the C-1.5 (path C combined with the RSR of 1:1.5) process are significantly increased, which significantly weakens the basal texture and improves the ductility of the alloy, greatly enhancing the processing and formability of ZK60 magnesium alloy.