Harus Laksana Guntur

Dr. Harus Laksana Guntur


Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 January 2006 in Measurement Science and Technology
Verified
Journal Article
Closed access
HGHarus Laksana Guntur
Harus Laksana Guntur
MCMaolin Cai
Maolin Cai
KKKenji Kawashima
Kenji Kawashima
TKToshiharu Kagawa
Toshiharu Kagawa

19 September 2025 in World Electric Vehicle Journal
Verified
Journal Article
Open access
PDF file
MAMuhammad Hasan Albana
Muhammad Hasan Albana
NBNinda Hardina Batubara
Ninda Hardina Batubara
NNNovebriantika Novebriantika
Novebriantika Novebriantika
MSMeschac Timothee Silalahi
Meschac Timothee Silalahi
YYYogantara Yogantara
Yogantara Yogantara
HGHarus Laksana Guntur
Harus Laksana Guntur
Mitigating heat generation in electric vehicle (EV) batteries is crucial for safety, operational efficiency, and battery lifespan. Liquid-cooled cold plates are widely used; however, comparative studies of channel geometries are often hindered by inconsistent experimental conditions. This study systematically compares six cold plate configurations under identical cross-sectional areas and uniform thermal boundary conditions. These controls isolate the effect of geometry on performance. Computational fluid dynamics (CFDs) was used to evaluate six configurations, derived from three main channel layouts (serpentine with eight U-turns, serpentine with six U-turns, and elliptical) and two cross-sectional shapes (circular and square). The serpentine square-tube design with eight U-turns exhibited the lowest thermal resistance (0.0159 K/W). The circular-tube variant achieved the most uniform temperature distribution (TUI > 0.53). The six U-turn circular-tube configuration demonstrated the lowest pressure drop (11.7 kPa). The results indicate that no single design optimizes all performance metrics, highlighting trade-offs between cooling effectiveness, temperature uniformity, and hydraulic efficiency. By isolating geometric variables, this study offers targeted design recommendations for engineers developing battery thermal management systems (BTMS).

13 July 2018 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
HGHarus Laksana Guntur
Harus Laksana Guntur
WHWiwiek Hendrowati
Wiwiek Hendrowati
NSNovian Fajar Satria
Novian Fajar Satria
HSHary Soebagyo
Hary Soebagyo
This paper reports the result of modelling and analysis of the pressure response and the regenerated energy of two different mechanism of energy regenerating shock absorber with 1) Single Input Hydarulic Cylinder-Single Output Generator (SISO), and 2) Double Input Hydraulic Cylinder-Single Ouput Generator (DISO). The recently developed and researched hydraulic based regenerative shock absorber uses SISO concept, which convert the vibration energy of one suspension into electricity using one magneto-electric generator. In this research, the new concept of converting vibration energy from two input suspesion simultaneously with one generator, DISO is proposed to improve the continuity of energy supply and the output power. The SISO and DISO are mathematicaly modelled and simulated. For SISO, the simulated inlet pressure shows a periodic trend with maksimum pressure of 1.2 MPa. This inlet pressure can produce hydarulic motor’s maximum output torque of 1-1.5 Nm. Meanwhile, DISO can produce inlet pressure with maksimum pressure of 1.2 MPa and hydarulic motor’s maximum output torque of 1.2-1.6 Nm. This simulation results show that DISO has better performance than SISO. The detail results are discussed in this paper.

1 January 2019
Verified
Conference Paper
Closed access
DNDhion Khairul Nugraha
Dhion Khairul Nugraha
HGHarus Laksana Guntur
Harus Laksana Guntur

13 July 2018 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
HGHarus Laksana Guntur
Harus Laksana Guntur
ADAida Annisa Amin Daman
Aida Annisa Amin Daman
WHWiwiek Hendrowati
Wiwiek Hendrowati
DMDidin Merlinovi
Didin Merlinovi
SHSoebagyo Hary
Soebagyo Hary
Shock absorber is designed to convert the kinetic energy from impact into heat energy that is dissipated. The dissipated energy that is produced by conventional shock absorber is wasted. The aim of this paper is to design the shock absorber that can damp the impact and can harvest energy at the same time. It is called Hydro-Magneto-Electric Regenerative Shock Absorber (HMERSA). This research simulated the HMERSA that applied on a front and rear suspension system of a car. The car speed was varied from 0 km/h to 80 km/h. The phase difference of front and rear suspension’s input were 0° and 90°. The results show that the highest power generated is 165 Watt at car speed of 80 km/h and occurred when the phase difference was 0°.

1 January 2016 in International Journal of Vehicle Systems Modelling and Testing
Verified
Journal Article
Closed access
HGHarus Laksana Guntur
Harus Laksana Guntur
LSListy Fazria Setiawan
Listy Fazria Setiawan
This research focuses on the study of the influence of asymmetrical characteristics of damping force on the ride quality of a typical passenger car. With different standard road inputs, variation of severity parameter, asymmetry ratios, asymetry average as well as the velocity of the vehicle, performance indices and root mean square (RMS) values of acceleration of the sprung mass in respect to vehicle velocity are derived so that the efficacy of the asymmetrical systems can be assessed. The comparison between the symmetrical and asymmetrical systems subjected to the modified bump inputs showed that the asymmetrical system, with nonlinear characteristics and asymmetry ratio above 1, tends to have a smoother and more progressive performance. The comparison between the symmetrical and asymmetrical systems subjected to harmonic inputs showed that the asymmetry ratio of the systems does not influence the performance, instead the asymmetry average does.