Xu Gao

Dr. Xu Gao


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2024 in Sensors
Verified
Journal Article
Open access
PDF file
XGXu Gao
Xu Gao
JZJing Zhou
Jing Zhou
XDXiao Du
Xiao Du
Piezoelectric transducers are commonly used in acoustic well logging. However, the low frequency and narrow range of the acoustic waves limit the achievable detection accuracy. In addition, the low amplitude of the waves causes useful information to be easily masked by noise during detection, which affects the accuracy of geological identification and makes it difficult to detect formations tens of meters away. This paper proposes a microporous liquid–electric transmission transducer, in which the microporous electrode structure generates a powerful shock wave through a high-energy instantaneous discharge. First, a model of the liquid–electric microporous transmitting transducer was constructed by combining simulations with numerical calculations, and its electro-acoustic characteristics were analyzed. Then, based on the survey requirements, two innovative optimization schemes for the microporous electrode structure were proposed, namely a triangular pyramid microporous electrode structure and a rectangular microporous electrode structure, and their performances were compared. The results show that the newly optimized triangular pyramid microporous electrode liquid–electric transducer generates acoustic waves with higher amplitude and a wider frequency range than conventional piezoelectric transducers and other microporous structures. It maintains high energy while achieving high frequencies, enabling detection at distances of up to hundreds of meters and the precise characterization of small geological bodies. This has significant implications for applications in marine exploration, land exploration, clean energy, and new energy fields.

12 September 2024 in Energies
Verified
Journal Article
Open access
PDF file
XGXu Gao
Xu Gao
JZJing Zhou
Jing Zhou
HXHaiming Xie
Haiming Xie
XDXiao Du
Xiao Du
The wave frequency and energy of traditional piezoelectric emission sources used in acoustic logging are limited, which results in an inadequate detection resolution for measuring small-scale geological formations. Additionally, the propagation of these waves in formations is prone to loss and noise interference, restricting detection to only a few tens of meters around the well. This paper investigates an impulse sound source, a new emission source that can effectively enhance the frequency range and wave energy of traditional sources by generating excitation waves through high-voltage discharges in a fluid-penetrated electrode structure. Firstly, a high-voltage circuit experimental system for the impulse sound source was constructed, and the discharge and response characteristics were experimentally analyzed. Then, four types of needle series electrode structure models were developed to investigate and compare the effects of different electrode structures on the impulse sound source, with the needle-ring electrode demonstrating superior performance. Finally, the needle-ring electrode structure was optimized to develop a ball-tipped needle-ring electrode, which is more suitable for acoustic logging. The results show that the electrode structure directly influences the discharge characteristics of the impulse sound source. After comparison and optimization, the final ball-tipped needle-ring electrode exhibited a broader frequency range—from zero to several hundred thousand Hz—while maintaining a high acoustic amplitude. It has the capability to detect geological areas beyond 100 m and is effective for evaluating micro-fractures and small fracture blocks near wells that require high detection accuracy. This is of significant importance in oil, gas, new energy, and other drilling fields.

20 June 2025 in Energies
Verified
Journal Article
Open access
PDF file
XDXiao Du
Xiao Du
JZJing Zhou
Jing Zhou
XGXu Gao
Xu Gao
The high-power drive of an impulse sound source with drilling makes the system’s life short and difficult to integrate. This report firstly establishes the pulse discharge experimental system and finite element model, and compares and verifies the typical parameters. Second, the study examines how the energy storage capacitor’s charging voltage, discharge electrode gap, and liquid environment conductivity influence the electroacoustic performance of needle series electrodes. Subsequently, the optimal electrode configuration is identified under power constraints, yielding electroacoustic parameters and curves suitable for low-power impulsive sound sources. The findings reveal that the needle–plate electrode outperforms others in pre-breakdown duration, peak impulse wave strength, highest sound pressure level, and electroacoustic conversion efficiency. However, its higher power demand can be mitigated by lowering the charging voltage and narrowing the electrode gap. The charging voltage of the power-limited needle–plate electrode is only 3.5 kV, the impulse wave intensity reaches 1.27 MPa, and the peak system power is effectively controlled within 6.66 kW. A stable 288 dB SPL output is maintained up to 1 kHz, and above 250 dB in the wide bandwidth of 1–100 kHz. Needle–plate electrodes provide broadband excitation and high intensity SPL output despite power limitations.

7 April 2025 in Sensors
Verified
Journal Article
Open access
PDF file
XDXiao Du
Xiao Du
JZJing Zhou
Jing Zhou
XGXu Gao
Xu Gao
In acoustic deep detection technology, conventional monopole, dipole, and phased-array sound sources are far inferior to impulsive sound sources in frequency and amplitude. But impulse sound sources mostly work under high-power, high-voltage, and high-current conditions, which are difficult to be applied downhole. The purpose of this paper is to reduce the power of the impulse sound source system and at the same time to stimulate excellent impulse wave characteristics. Firstly, an experimental impulse sound source system using needle-rod electrodes was constructed, and the discharge experimental results were analysed. Secondly, a finite element model of the needle-rod electrodes of the impulse sound source was established based on the experimental conditions, and the effects of the charging voltage, electrode gap, and liquid conductivity on the power and electroacoustic parameters of the needle-rod electrodes system were investigated separately. Finally, the optimised electroacoustic parameters and curves of the needle-rod electrodes of the low-power impulse sound source were obtained. The results show that the charging voltage is the most significant parameter affecting the power of the needle-rod electrode system; a larger liquid conductivity and a suitable electrode gap are required for the optimal impulse wave parameters. The optimised low-power impulse sound source system with needle-bar electrodes with a power of 20.95 kW achieves an impulse wave intensity of 4.78 MPa, with a sound pressure level above 295 dB up to 1 kHz and above 225 dB from 1 kHz to 300 kHz. Optimised needle-rod electrodes for low-power impulse sound sources have the advantages of a wide bandwidth and high energy. This makes the downhole application of low-power impulse sound sources possible, which will play an important role in oil exploration and other drilling exploration fields.

10 March 2025 in Sensors
Verified
Journal Article
Open access
PDF file
XGXu Gao
Xu Gao
JZJing Zhou
Jing Zhou
XDXiao Du
Xiao Du
Traditional emitters used for downhole acoustic detection have limited radiation frequency and energy, making it difficult to transmit high-precision acoustic signals over long distances. This paper presents a plasma emitter in which high-pressure discharge generates a powerful spherical impulse wave with a wide frequency range. First, the discharge characteristics of the plasma needle-plate emitter are analyzed using high-voltage discharge experiments and discharge simulation models for underwater emitters. Subsequently, advanced modifications are made to the structure of the needle–plate emitter to meet the requirements of downhole detection. A new type of hollow needle–plate emitter with a spherical tip is developed. The results show that the structural optimization of the hollow needle–plate emitter with a spherical tip resulted in a 27.2% increase in impulse wave amplitude, a 28.1% improvement in electro-acoustic conversion efficiency, and a radiation frequency band covering up to 100 kHz. This development is conducive to more accurate and longer-range downhole structure detection. The detection range outside the borehole can reach tens to hundreds of meters. This enables the precise control of the wellbore path and reduces the demands on the rig’s build rate. The emitter has significant application potential in areas such as onshore and offshore oil and gas exploration, unconventional resource detection, impulse wave fracturing and wellbore clearance, and rescue and U-well drilling.