When combining contactless power and data transfer, antennas are often placed near magnetic materials with unknown RF properties. While permittivity measurement methods for dielectric materials at RF frequencies are well established, methods for permeability measurement are relatively scarce and often cumbersome. We propose a versatile and easy-to-use method that is applicable to both dielectric and magnetic materials, which uses a coplanar waveguide structure to measure the complex permittivity and permeability in the 1-16 GHz range. We combine the Nicolson-Ross-Weir algorithm with a robust root selection and a conformal mapping method to extract the permittivity and permeability from the measurement data. Moreover, we propose a novel calibration method that uses a single reference dielectric to increase the accuracy of the measured permittivity significantly, even when measuring magnetic materials.
6 October 2022 in IEEE Antennas and Propagation Magazine
Recent wireless communication systems, including the 5G communication New Radio (NR) operating in the millimeter-wave (mm-wave) bands, demand performance measurements using an over-the-air (OTA) test instead of using the traditional conducted methods. This article provides an overview of various OTA measurement systems that measure the integrated antenna inside a 5G-and-beyond mm-wave device, including the direct far-field (DFF), indirect FF (IFF), near-field (NF), and midfield measurements. By considering several significant parameters, including minimum measurement distance required, metrics that can be measured, and complexity of the electrical and mechanical components of the system, suitable OTA measurement methods for integrated antennas can be selected. Furthermore, factors contributing to the measurement uncertainty of OTA systems based on the technical report (TR) of the 3rd Generation Partnership Project (3GPP) are summarized and discussed. By analyzing the significant parameters of each OTA system and contributors of the measurement uncertainty, the reader can determine the OTA method that is most suitable to measure the integrated antennas for mm-wave communications.
26 July 2019 in IEEE Transactions on Antennas and Propagation
Frequency-reconfigurable antennas seem a viable solution to achieve better performance and increased flexibility for integrated mobile phone antennas. Due to the lossy nature of many tunable components, the use of multiple combined tuning components in a single design seems attractive, as it can distribute the current over the components. However, many combinations of individual tuning component settings can result in an acceptable input match, while they will vary significantly in terms of radiation efficiency. It is challenging to distinguish between these radiating and non-radiating tuning component settings during the design procedure. In this paper, we propose a method to determine the component settings with the highest efficiency at a desired operating frequency. The method uses a single full-wave simulation, which is combined with circuit-level calculations. We discuss how to apply the method in detail, and demonstrate its functionality with an inverted-L antenna sporting three tunable BST capacitors. It is shown that the method can successfully predict tuning component settings for high antenna efficiency over a 1.4 to 2.8 GHz tuning band, with total efficiencies up to 35% and radiation efficiencies up to 50%. The method can easily be applied to any desired antenna geometry.
5 April 2021 in IEEE Transactions on Antennas and Propagation
The Friis equation is often used to determine the gain of antennas but assumes that far-field conditions are met. For limited antenna separations on the order of the Fraunhofer distance, its use requires a precise estimate of the amplitude centers of the antennas. Using a new antenna gain measurement technique, it is shown that the amplitude center can be very well estimated and that the measurement results can be used to confirm that far-field conditions are met. Moreover, reflections caused by scatterers are averaged since multiple measurements are performed. The presented method is particularly useful for anechoic chambers that are limited in size, such as small anechoic chambers for the characterization of, for instance, 5G millimeter-wave phased arrays.
The need for accurate efficiency measurements at high frequencies of large form-factor devices is ever increasing. In this work, the potential of performing antenna efficiency measurements in an electrically extremely large (up to 250λ) reverberation chamber is investigated and compared to its use at lower frequencies. It is found that there are large deviations in the enhanced backscattering constant at high frequencies. Closer investigation, by introducing a position-dependent enhanced backscattering constant calculation, shows that the deviation mostly occurs at the horn antenna directed at the stirrer. This could be aggravated by the use of a moving wall type of stirrer. The work concludes by demonstrating the potential impact of these deviations on the antenna efficiency. The deviations clearly show the need for more research into these effects.