Aiman Al-Allaq

Mr. Aiman Al-Allaq


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 March 2025 in Materials Chemistry and Physics
Verified
Journal Article
Closed access
AAAiman Al-Allaq
Aiman Al-Allaq
NTN. Tabassum
N. Tabassum
YMY.S. Mohammed
Y.S. Mohammed
AEA.A Elmustafa
A.A Elmustafa

9 January 2026 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
AAAiman Al-Allaq
Aiman Al-Allaq
NTN. Tabassum
N. Tabassum
YMY.S. Mohammed
Y.S. Mohammed
AEA.A Elmustafa
A.A Elmustafa

29 April 2025 in Journal of Vacuum Science & Technology B
Verified
Journal Article
Closed access
AAAiman Al-Allaq
Aiman Al-Allaq
AMAbdullah Mamun
Abdullah Mamun
MPMatt Poelker
Matt Poelker
AEA.A Elmustafa
A.A Elmustafa
The hydrogen outgassing rate of a vacuum chamber made of AISI 1020 low-carbon steel was found to be notably smaller than a similar chamber made of AISI 316L stainless steel following heat treatment at 150 °C. When the chambers were baked at 400 °C, the outgassing rate of the 1020 low-carbon steel chamber was approximately 2000 times smaller than that of the 316L stainless-steel chamber. After quantifying hydrogen outgassing rates, vacuum chambers made of 1020 low-carbon steel and 316L stainless steel were heated for a prescribed duration and then pumped with an ion pump and nonevaporable getter pump to reach “ultimate pressure.” The 1020 low-carbon steel chamber reached lower pressures than the 316L stainless-steel chamber. Monte Carlo simulation predictions using the measured hydrogen outgassing rates are in good agreement with the ultimate pressure measurements. Our measurements indicate that low-carbon steel can provide pressures within the extreme high vacuum range (<7.5 × 10−13 Torr) if care is taken to minimize the surface area contribution from stainless steel.

1 December 2025 in Journal of Vacuum Science & Technology B
Verified
Journal Article
Closed access
AAAiman Al-Allaq
Aiman Al-Allaq
AMAbdullah Mamun
Abdullah Mamun
MPMatt Poelker
Matt Poelker
AEA.A Elmustafa
A.A Elmustafa
The outgassing properties of bare and magnetite-coated AISI 1020 low-carbon steel vacuum chambers were evaluated to establish material selection criteria for extreme high vacuum applications, namely, to explore the possibility of using these materials to build next-generation spin-polarized photoelectron guns. Water outgassing measurements using the throughput method revealed that the magnetite-coated chamber exhibited five times lower outgassing at room temperature prior to baking, but this advantage disappears after 80 °C baking. Hydrogen outgassing measurements demonstrated significant differences after intensive heat treatment: the bare low-carbon steel vacuum chamber achieved a specific outgassing rate of 9.6 × 10−16 Torr L s−1 cm−2 after 400 °C/50 h bake plus additional heat treatment at lower temperatures, 25 times lower than the magnetite-coated low-carbon steel chamber. Residual gas analysis showed >99% hydrogen composition after heat treatment for both materials, with carbon species below detection limits for bare low-carbon steel versus 0.8% for magnetite-coated surfaces. These measurements indicate that properly conditioned bare low-carbon steel can achieve the <10−12 Torr pressures required for next-generation spin-polarized photogun applications. The paper includes various analysis techniques intended to explain observed behaviors: isotherm analysis of pump-down plots, Arrhenius analysis of hydrogen outgassing rate data, and residual gas composition tracking.

1 July 2024 in Journal of Engineering and Sustainable Development
Verified
Journal Article
Open access
PDF file
SAShahad Fadhil Alrubaye
Shahad Fadhil Alrubaye
NANaseer Alhaboubi
Naseer Alhaboubi
HAHussein A. Al-Amili
Hussein A. Al-Amili
AAAiman Al-Allaq
Aiman Al-Allaq
DMDhuha Ahmed Mohammed
Dhuha Ahmed Mohammed
The present study focuses on the technique of hardness removal by using a novel reactor performing an electrocoagulation (EC) process. The variation of alkalinity is also recorded. Continuous flow experiments were conducted for Total Hardness (TH) removal using a transparent plastic reactor using aluminum plate electrodes that have holes so that the water flows through the plates in a zigzag way. The influence of various operating parameters such as the number of plates (two and four), flow rate (600, 1000 L/h), and water type (Tigris River & rejected water from Reverse Osmosis system RO) was investigated. The results showed that an increase in the number of electrodes led to an increase in the total hardness removal efficiency. In addition, the increase in the flow rate led to a decrease in the removal efficiency. For the rejected RO water type, the highest hardness removal rate was 16.16% for 4 plates electrodes and 600 L/h flow rate while for the river water was 29% for 4 plates electrodes and 1000 L/h.

30 April 2024 in Metals
Verified
Journal Article
Open access
PDF file
AAAiman Al-Allaq
Aiman Al-Allaq
JMJoseph Maniscalco
Joseph Maniscalco
SBSRINIVASA BHUKYA
SRINIVASA BHUKYA
ZWZhenhua Wu
Zhenhua Wu
AEA.A Elmustafa
A.A Elmustafa
This study presents an optimization of the process parameters for the effect of copper (Cu) donor material percentage on the friction stir welding (FSW) of AA6061-T6 alloy. Extensive factorial experiments were conducted to determine the significance of the rotational speed (ω), the transverse speed (v), the interface coefficient of friction (μ), and the Cu donor material percentage in the plunge, left, right, and downstream zones. Design Expert 13 software was used to identify the number of simulation experiments to be conducted using the Abaqus simulation software. From Design Expert 13, which is a thorough multi-objective optimization analysis software, we were able to identify ideal welding parameters such as a rotational speed of 1222 rpm, transverse speed of 1.1 mm/s, the coefficient of friction of 0.9, and a 19% donor material percentage for the plunge zone. Significant findings demonstrate that increasing the Cu donor material substantially reduced the temperature from 502 °C to 134 °C when the Cu content is increased from 0% to 50%. This integrated modeling and optimization approach provides a practical procedure to identify the best experimental parameters for the process and a new understanding to guide advances for high-quality FSW of aluminum alloys. This work offers a methodology for optimizing the FSW parameters aligned with multifaceted thermomechanical physics.