Titanium boride (TiB2) is a material classified as an ultra-high-temperature ceramic. The TiB2 structure is dominated by covalent bonds, which gives the materials based on TiB2 very good mechanical and thermal properties, making them difficult to sinter at the same time. Obtaining dense TiB2 polycrystals requires a chemical or physical sintering activation. Carbon and molybdenum disilicide (MoSi2) were chosen as sintering activation additives. Three series of samples were made, the first one with carbon additives: 0 to 4 wt.%; the second used 2.5, 5 and 10 wt.% MoSi2; and the third with both additions of 2 wt.% carbon and 2.5, 5 and 10 wt.% MoSi2. On the basis of the dilatometric sintering analysis, all additives were found to have a favourable effect on the sinterability of TiB2, and it was determined that sintering TiB2 with the addition of carbon can be carried at 2100 °C and with MoSi2 and both additives at 1800 °C. The polycrystals were sintered using the hot-pressing technique. On the basis of the studies conducted in this work, it was found that the addition of 1 wt.% of carbon allows single-phase TiB2 polycrystals of high density (>90%) to be obtained. The minimum MoSi2 addition, required to obtain dense sinters with a cermet-like microstructure, was 5 wt.%. High density was also achieved by the materials containing both additives. The samples with higher MoSi2 content, i.e., 5 and 10%, showed densities close to 100%. The mechanical properties, such as Young’s modulus, hardness and fracture toughness (KIc), of the polycrystals and composites were similar for samples with densities exceeding 95%. The Vickers hardness was 23 to 27 GPa, fracture toughness (KIC) was 4 to 6 MPa·m0.5 and the Young’s modulus was 480 to 540 GPa. The resulting TiB2-based materials showed potential in high-temperature applications.
In this study, we investigated the effect of adding two different intermetallics, Ti5Si3 and TiSi2, for the preparation of TiB2-SiC-B4C composites. As part of the research, stoichiometric composites consisting only of two phases TiB2 and SiC were obtained. The TiB2-SiC-B4C composites were prepared via pressureless sintering. The presence of the phases in the sintered composites was confirmed using X-ray diffraction and scanning electron microscopy. The SEM-EDS examination revealed that the TiB2 and SiC phases were formed during the composite process synthesis and were distributed homogeneously in the B4C matrix. The obtained results allowed us to usually exceed 2000 °C and the use of specialized equipment for firing, that is, vacuum or protective atmosphere furnaces as well as control and measurement equipment. Such an approach generates high costs that are decisive for the economics of the technological processes. In the case of our compositions, it is possible to lower the temperature to 1650 °C. The TiB2-SiC-B4C composites were classified as UHTCs.
ZrB2-HfB2 composites allow us to obtain materials characterized by the high chemical resistance characteristic of HfB2 while reducing density and improving sinterability due to the presence of ZrB2. Since boride composites are difficult-to-sinter materials. One way to achieve high density during sintering is to add phases that activate mass transport processes and, after sintering, remain as composite components that do not degrade and even improve some properties of the borides. The following paper is a comprehensive review of the effects of various and the most commonly used sintering aids, i.e., SiC, B4C, WC, MoSi2, and CrSi2, on the thermo-chemical properties of the ZrB2-HfB2 composites. High-density composites with a complex phase composition dominated by (Zr,Hf)B2 solid solutions were obtained using a hot pressing method. The tests showed differences in the properties of the composites due to the type of sintering additives used. From the point of view of the thermo-chemical properties, the best additive was silicon carbide. The composites containing SiC, when compared to the initial, pure borides, were characterized by high thermal conductivity λ (80–150 W/m·K at 20–1000 °C), a significantly reduced thermal expansion coefficient (CTE ~6.20 × 10−6 1/K at 20–1000 °C), and considerably improved oxidation resistance (up to 1400 °C).