Eunsung Shin

Dr. Eunsung Shin

Electrical & Computer Engineering, University of Dayton, Dayton, Kentucky, USA

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 January 2024 in Crystals
Verified
Journal Article
Open access
PDF file
BABirhanu Alemayehu
Birhanu Alemayehu
ESEunsung Shin
Eunsung Shin
VVVladimir Vasilyev
Vladimir Vasilyev
GSGuru Subramanyam
Guru Subramanyam
Metallic transition-metal dichalcogenides are emerging as promising electrode materials for applications such as 2D electronic devices owing to their good electrical conductivity. In this study, a high-performance humidity sensor based on NbTe2 electrode material and an indium-doped SnO2 thin film sensing layer was fabricated using a pulsed laser deposition system. The morphology, structural, elemental compositions, and electrical properties of the as-deposited samples were characterized. Additionally, the humidity sensing response of the fabricated sensor with In-doped SnO2 (8:92 wt%) sensing film was evaluated in a wide range of relative humidity at room temperature. The results demonstrated that the humidity sensor based on In-doped SnO2 exhibited a high sensitivity of 103.1 Ω/%RH, fast response and recovery times, a low hysteresis value, good linearity, and repeatability. In addition, the sensor had good long-term stability, with a variation in impedance of less than 3%. The results indicated that the humidity sensor could be suitable for practical humidity sensing applications.

12 April 2024 in Crystals
Verified
Journal Article
Open access
PDF file
BABirhanu Alemayehu
Birhanu Alemayehu
KAKaushik Annam
Kaushik Annam
ESEunsung Shin
Eunsung Shin
GSGuru Subramanyam
Guru Subramanyam
SnO2-based gas sensors have been widely synthesized and used for the detection of various hazardous gases. However, the use of doped SnO2 in sensing applications has recently attracted increased interest due to the formation of a synergistic effect between the dopant and the host. Moreover, in the case of a surface acoustic wave (SAW) sensor, the piezoelectric material used in the fabrication of the sensor plays a crucial role in defining the response of the SAW sensor. As a ferroelectric material, barium strontium titanate (Ba0.6Sr0.4TiO3) has recently been studied due to its intriguing dielectric and electromechanical properties. Its high acoustic velocity and coupling coefficient make it a promising candidate for the development of acoustic devices; however, its use as a piezoelectric material in SAW sensors is still in its infancy. In this paper, we present the design, fabrication and validation of an indium doped SnO2-based SAW gas sensor on Ba0.6Sr0.4TiO3 thin film for room temperature (RT) applications. Pulsed laser deposition was used to deposit thin films of Ba0.6Sr0.4TiO3 and indium-doped SnO2. Different characterization techniques were employed to analyze the morphology and crystallization of the films. The performance of the fabricated sensor was validated by exposing it to different concentrations of ethanol and then analyzing the recorded frequency shift. The sensor exhibited fast response (39 s) and recovery (50 s) times with a sensitivity of 9.9 MHz/Δ. Moreover, the sensor had good linear response and reproducibility. The fabricated indium-doped SnO2-based SAW gas sensor could be suitable for practical room temperature applications.

31 December 2024 in Micromachines
Verified
Journal Article
Open access
PDF file
KAKaushik Annam
Kaushik Annam
BABirhanu Alemayehu
Birhanu Alemayehu
ESEunsung Shin
Eunsung Shin
GSGuru Subramanyam
Guru Subramanyam
This paper explores the potential of phase change materials (PCM) for dynamically tuning the frequency response of a dumbbell u-slot defected ground structure (DGS)-based band stop filter. The DGSs are designed using co-planar waveguide (CPW) line structure on top of a barium strontium titanate (Ba0.6Sr0.4TiO3) (BST) thin film. BST film is used as the high-dielectric material for the planar DGS. Lower insertion loss of less than −2 dB below the lower cutoff frequency, and enhanced band-rejection with notch depth of −39.64 dB at 27.75 GHz is achieved by cascading two-unit cells, compared to −12.26 dB rejection with a single-unit cell using BST thin film only. Further tunability is achieved by using a germanium telluride (GeTe) PCM layer. The electrical properties of PCM can be reversibly altered by transitioning between amorphous and crystalline phases. We demonstrate that incorporating a PCM layer into a DGS device allows for significant tuning of the resonance frequency: a shift in resonance frequency from 30.75 GHz to 33 GHz with a frequency shift of 2.25 GHz is achieved, i.e., 7.32% tuning is shown with a single DGS cell. Furthermore, by cascading two DGS cells with PCM, an even wider tuning range is achievable: a shift in resonance frequency from 27 GHz to 30.25 GHz with a frequency shift of 3.25 GHz is achieved, i.e., 12.04% tuning is shown by cascading two DGS cells. The results are validated through simulations and measurements, showcasing excellent agreement.