The structure and optic properties of the transparent PP+SiO2 nanocomposites with a relatively high refractive index and enhanced luminescence properties were investigated. X-ray analysis, Fourier-transform infrared (FTIR), Visible-ultraviolet, and photoluminescence spectroscopic methods were used for investigation. The XRD analysis indicated that the fraction of the amorphous phase of the polycrystalline polymer decreases with the introduction of SiO2 nanoparticles. Even though SiO2 nanoparticle is amorphous itself, they play the role of the crystallinity centers in the polymer matrix, and the degree of crystallinity increases in polymer nanocomposites. According to UV-vis spectroscopic analysis that, with the increasing of the concentration of SiO2 nanoparticles distributed in the polymer matrix, the absorption intensity of the samples also increases. It was explained by the hyperchromic effect which is related to raising the optical density of the polymer by introducing the filler particles (SiO2). It was calculated bandgap energy and refractive index on the base of the UV spectra of samples. It has been found that at low concentrations of amorphous silica nanoparticles, the polymer nanocomposite retains its transparency despite having a relatively high refractive index (1.96). Furthermore, the photoluminescence (PL) spectrum of nanocomposites was investigated depending on filler concentration. It was clear that the intensity of the PL spectrums increases with the increase of the filler concentration that is explained by the raising of the luminescence centers in the nanocomposite material. These luminescence centers are oxygen-deficit centers in the spatial structure of the amorphous silica nanoparticles.
14 February 2019 in Journal of Elastomers & Plastics
Poly(vinyl chloride) (PVC)–cadmium sulfide (CdS) nanocomposite films were successfully synthesized by ex situ solution casting method. Scanning electron microscopy showed that CdS nanoparticles are well monodispersed in the PVC matrix. From the ultraviolet (UV) spectra of nanocomposites, the width of the forbidden band for polymer nanocomposites was determined by extrapolation method. UV-visible optical spectra revealed that the optical band of nanocomposites is increased with increasing concentration of CdS nanoparticles in the PVC matrix. It was found that the band gap is 3.8 eV for PVC-3% CdS nanocomposites, 2.7 eV for PVC-5% CdS, and 2.35 eV for PVC-10% CdS nanocomposites. Photoluminescence spectrum of PVC-CdS-based nanocomposites shows two luminescent peaks at the wavelengths of 436 nm and 472 nm at the luminescence spectrum which belongs to CdS nanoparticles. Photoluminescence study shows that PVC-CdS nanocomposites exhibit a great blue shift (approximately 100 nm) compared with bulk CdS nanoparticles.
Polymer nanocomposites based on polystyrene and polycrystalline Si nanoparticles have been successfully synthesized using the solution-casting method. The scanning electron microscope and x-ray diffraction methods show that the Si nanoparticle size in the obtained nanocomposite was up to 50 nm. The thermostability of the obtained nanocomposite was studied depending on the concentration of Si nanoparticles in the PS matrix. It was found that Si nanoparticles that are distributed homogeneously in the polymer matrix act as a thermal barrier. By adding 3% Si nanoparticles into polystyrene polymer, the thermal degradation temperature of PS increases by 20°, and the decomposition rate reduces from −42,460 mg/min to −35,099 mg/min. In addition, it was shown that Si nanoparticles do not affect the PS glass transition temperature, which explains that the porous Si does not reduce the free volume for the polymer molecules to move. The polymer macromolecules just are adsorbed on the porous silicon surface, which partially limits their mobility.
25 May 2025 in Journal of Thermoplastic Composite Materials
High-density polyethylene (HDPE) nanocomposites with Fe 3 O 4 nanoparticles were synthesized and analyzed for structural, thermal, and magnetic properties. X-ray diffraction showed an increase in Fe 3 O 4 crystallite size from 5.14 nm to 12.01 nm, while the HDPE crystalline size decreased from 14 nm to 4.88 nm for HDPE + 3% Fe 3 O 4 and HDPE + 40% Fe 3 O 4 , respectively. Thermogravimetric analysis showed improved thermal stability, with the onset temperature increasing from 243.78°C (HDPE) to 395.13°C (HDPE + 40% Fe 3 O 4 ). Differential scanning calorimetry indicated a crystallinity rise from 44.45% to 51.95% (HDPE + 40% Fe 3 O 4 ), while melting and crystallization temperatures remained near 104°C and 94°C, respectively. Magnetic characterization revealed that the saturation magnetization increased from 49.61 × 10 −3 emu for HDPE +1% Fe 3 O 4 to 52.98 × 10 −3 emu for HDPE +10% Fe 3 O 4 , while the coercivity decreased from 17.76 G for HDPE + 5% Fe 3 O 4 to 6.30 G for HDPE + 1% Fe 3 O 4 . This reduction in coercivity suggests a transition from a single-domain to a multi-domain state, likely due to nanoparticle aggregation at higher concentrations. These results demonstrate the potential of HDPE/Fe 3 O 4 nanocomposites for thermally stable and magnetically tunable applications.
In the present study, high-impact polystyrene (HIPS) nanocomposites filled with nano-silicon In the present study, high-impact polystyrene (HIPS) nanocomposites filled with nano-silicon particles (Si) and multi-walled carbon nanotubes (MWCNTs) were prepared, their structural, dielectric, and mechanical properties were investigated. X-ray diffraction (XRD) analysis confirmed the polycrystalline nature of Si nanoparticles and the preservation of the MWCNTs’graphitic (002) structure. Atomic Force Microscope (AFM) analysis confirmed that the addition of hybrid fillers leads to changes in the surface morphology. It was determined that the root mean square (RMS) surface roughness decreased from approximately 85 nm for pure MWCNTs to about 30 nm for the HIPS + Si + MWCNT nanocomposite. Dielectric measurements showed that the HIPS+1.5 wt.%Si+1.5 wt.%MWCNT nanocomposite exhibited the highest dielectric response. The dielectric constant increased by approximately 3.5 times at 1 kHz compared to neat HIPS. A relaxation maximum observed at 125 Hz and was corresponding to an effective relaxation time of τ = 1.27 m. At 200 kHz, the AC conductivity was calculated as σ ≈ 10 –8 S/cm, consistent with near-percolation behavior. Mechanical testing revealed that tensile strength increased from 14.06 MPa to 17.49 MPa with hybrid filler incorporation, while relative elongation decreased from 82% to 17.88%, indicating the typical stiffness–ductility trade-off. The results demonstrate that hybrid Si/MWCNT fillers induce synergistic effect on dielectric and mechanical performance in HIPS-based nanocomposites.