This paper presents a new method to calculate the cogging torque of the permanent magnet synchronous machine under load condition. Combined with the mathematical expression of the cogging torque, it is found that the cogging torque will be influenced by the load. In order to accurately analyze the torque ripple of the motor at low speed and high torque operation and make it possible to reduce the cogging torque under load condition, it is necessary to calculate the cogging torque accurately. A calculation method for the on-load cogging torque of the PMSM, which the cross magnetization and core saturation have been taken into consideration, is proposed in this paper. The finite element analysis (FEA) and field-oriented control (FOC) contribute to the method, which mainly consists of three parts: elimination of the reluctance torque, calculation of the average torque, and the ripple torque and the separation of the cogging torque. By using this method, the cogging torques of a 16-pole/24-slot PMSM under different load conditions has been calculated. The result shows a very good agreement between simulation and experiment, which verifies the feasibility and effectiveness of the proposed method.
This paper proposes a rotor design method suitable for double-layer interior permanent magnet synchronous motor (DIPMSM), which can reduce electromagnetic torque ripple and at the same time reduce the electromagnetic noise of the motor. In previous studies, the inverse cosine function (ICF) was used to modify the rotor shape for making the air gap flux density distribution sinusoidal under no-load conditions, which can reduce the torque ripple. However, conventional ICF can only be used in a single-layer interior rotor structure. Consequently, this paper proposes a piecewise inverse cosine function (PICF) based on ICF, which can be applied to DIPMSM. To verify the improvement of the proposed method in the electromagnetic and noise aspects of the motor, the electromagnetic model and a noise prediction model of the 36-slot/8-pole motor are established by the finite element method. The PICF model is compared with the prototype in the aspects of electromagnetic performance and noise. The torque ripple is reduced by 54.16%, from ± 2.4 Nm to ± 1.1 Nm, and the electromagnetic noise is reduced by about 4.9 dB. Finally, the accuracy of the noise prediction model is verified by the noise test of the prototype.
This paper proposes a direct torque control (DTC) of permanent magnet synchronous motor (PMSM) with high torque estimation accuracy. Based on the PMSM mathematical model considering iron loss resistance, this paper analyzes that when using stator current to estimate torque, the accuracy will be affected by iron loss resistance. Using stator magnetizing current can solve the current deviation caused by iron loss resistance and improve torque estimation accuracy. Since the stator magnetizing current cannot be obtained directly, a novel iron loss resistance observer based on the model reference adaptive system (MRAS) is designed to estimate iron loss resistance and stator magnetizing current simultaneously. Popov's hyperstability theory guarantees the stability of the designed observer. Finally, a 1kW PMSM experimental platform is constructed to verify the proposed method. Both the simulation and experimental results show that the designed observer is stable, and using stator magnetizing current to estimate torque has better accuracy than stator current.
24 December 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
In this article, a deadbeat predictive current control (DPCC) method based on gain factor self-tuning technology is proposed, which can effectively improve the dynamic response performance and robustness of the control system. Since the performance of DPCC is highly dependent on parameter accuracy, this paper establishes a closed-loop transfer function model of the DPCC method and analyzes in detail the impact of parameter mismatch on the current dynamic response performance. Then, the current error caused by parameter mismatch is suppressed by designing the gain factor, on this basis, a parameter self-tuning algorithm based on gradient descent optimization method is constructed. Compared with traditional parameter identification algorithms, the proposed method has the advantages of strong versatility and greatly reduces computational burden. Finally, the accuracy of the tuning results of the proposed method is proved by experimental results, which effectively suppresses the influence of parameter mismatch and improves the current response performance.
This paper presents a phase-inductance-based position estimation method for interior permanent magnet synchronous motors (IPMSMs). According to the characteristics of phase induction of IPMSMs, the corresponding relationship of the rotor position and the phase inductance is obtained. In order to eliminate the effect of the zero-sequence component of phase inductance and reduce the rotor position estimation error, the phase inductance difference is employed. With the iterative computation of inductance vectors, the position plane is further subdivided, and the rotor position is extracted by comparing the amplitudes of inductance vectors. To decrease the consumption of computer resources and increase the practicability, a simplified implementation is also investigated. In this method, the rotor position information is achieved easily, with several basic math operations and logical comparisons of phase inductances, without any coordinate transformation or trigonometric function calculation. Based on this position estimation method, the field orientated control (FOC) strategy is established, and the detailed implementation is also provided. A series of experiment results from a prototype demonstrate the correctness and feasibility of the proposed method.
This paper presents inductance characteristics analysis of the consequent-pole permanent magnet in-wheel motor (CPM). Considering the specialty of consequent-pole structure, this paper analyzes the change rule of the winding self-inductance via equivalent magnetic circuit method (EMCM). The corresponding equivalent resistance is directly given when the rotor is in different positions. Based on this, equivalent magnetic circuit (EMC) that reflects the inductance of the CPM is summarized in this paper. In order to analyze the difference and connection of the inductance among the CPM, two models with 36 slots 32 poles and 48 slots 40 poles are established and compared. Moreover, the Fourier analysis expression of winding self-inductance is deduced to prove the different periodicities of winding self-inductance between two motors. Experimental result is consistent with the theoretical analysis, and the conclusion effectively proves the close relationship between the inductance characteristics and its internal structure of the motor.