Electric drives consume a great amount of the world’s energy, and it will keep increasing due to the electromobility trend. Thus, the efficiency of electric drives must be improved to reach the desired sustainability goal. The Silicon Carbide devices contribute to this objective due to their high working frequency and lower switching losses. However, working at higher frequencies may bring serious Electromagnetic Compatibility (EMC) problems, as well as insulation stress and higher bearing currents. Hence, it is important to have an electrical machine electrical equivalent circuit model to predict the electromagnetic interference levels. This review summarizes the current state of the art in electrical machine modeling and analysis in high frequency. The main analysis tools as Finite Element Methods, analytic and measurement-based tools are compared in their application on high-frequency electrical machine analysis. Then, different machine high-frequency models are reported, detailing their individual features. Additionally, the influence of the machine design parameters in EMC behavior is outlined for future analysis. All in all, Finite Element analysis is the most accurate tool for high-frequency analysis, provided that mesh size is thinner than the skin depth. It is also concluded that the winding placement is an essential parameter to define the high-frequency behavior of the machine.

The trend towards electrification in mobility has led to the increased use of silicon carbide (SiC) semiconductors. These semiconductors are more efficient but also present challenges related to electromagnetic interference (EMI) due to their higher voltage derivatives. This paper introduces a new high-frequency impedance model for electrical machines. The proposed model distinguishes itself from existing approaches by being entirely derived from Finite Element Method (FEM) simulations, which include capacitances in the magnetic simulation. This approach achieves a balance between computational efficiency and high accuracy across the entire frequency spectrum, ranging from 100 Hz to 50 MHz. The model provides valuable insights during the design phase and was rigorously validated using data from 28 samples of an industrial machine.

Linear switched-flux machines are a kind of permanent magnet machine with a passive ferromagnetic secondary. Therefore, they can achieve both a good performance and a low cost in long stroke applications. However, due to the end effect, these machines generate high detent force and on load thrust force ripples. There are several solutions in the literature that aim to minimise the thrust ripple. One of those solutions is the placement of additional poles in the ends of the machine. These can be passive, i. e. simple ferromagnetic teeth, or active, with additional magnets. The former is the most common solution in the literature. In this article, the optimal configuration of the additional poles is discussed via 4 additional pole sizing strategies, and the influence of the design variables and optimisation objectives is analysed. Then, a generic additional pole configuration is proposed, which combines a high effectiveness and a simple design. Finally, an experimental validation is carried out, and the measurements confirm the results from the optimisation.

Due to their particular structure, switched-flux permanent magnet machines have become a very interesting alternative for many applications. This is why some recent studies have been focused in the understanding of the operating mechanism of these machines via the MMF-permeance modelling. However, the models that can be found in the literature make some simplifications that reduce their accuracy when predicting the performance of switched-flux machines. For example, the models that can be found in the literature are commonly not precise enough for machines with a wide slot, because the influence of the modulator of the primary side of the machine is neglected. In this article, a precise analytical model is developed for a 6/13 C-Core switched-flux machine via a combination of a magnetic equivalent circuit and a MMF-permeance model. The model is based on the magnetic field modulation principle. The analytical model is used to explain the flux focusing effect and the force generation mechanism of switched-flux machines. A new concept of PM field harmonic efficiency ratio is used to identify the most efficient PM field harmonics of 2 switched-flux machines. The precision of the model is validated via 2D and 3D Finite Element Method simulations, and experimental measurements that were obtained with a linear machine prototype. The results show that the model can predict the performance of switched-flux machines with a high accuracy level.

The thermal design is one of the most important stages in the design process of electrical machines. Thanks to software packages, like Motor-CAD, rotating machine designers can predict the thermal operation of the machines with high precision. However, a Motor-CAD equivalent for linear machines does not exist. Thus, linear machine designers must develop specific thermal analysis tools when designing the machines. In this article, a generic thermal analysis tool for different kinds of linear machines is presented. The model has been designed in MATLAB Simulink. Hence, it should be easy to implement for most engineers. The article describes the configuration of the different elements of the tool. The calibration parameters and procedure, and typical values of the calibration variables, are also given in the document. Finally, in order to demonstrate the generic nature of the tool, the model is experimentally validated via DC thermal tests to a linear induction machine and a linear switched-flux permanent magnet machine. The results show that, despite being simple and easy to implement, the model can predict the thermal operation of different machines with high precision.

With increasing emphasis on energy efficiency and the widespread adoption of Wide-Band-Gap (WBG) devices, understanding and mitigating EMI is crucial for the reliability and performance of electric drives. This research focuses on high-frequency phenomena induced in electrical machines and the integration of Finite Element Method (FEM) simulations into the drive design process. A novel approach is introduced where a full drive model is experimentally validated using motor impedance obtained from FEM simulations, which is then fitted to a lumped-parameter model with a basic genetic algorithm. The model is validated across the full Electromagnetic Compatibility (EMC) range for conducted emissions, from 10 kHz to 30 MHz. The paper emphasises the importance of an EMI-focused design approach early in the development process to minimise costs, improve reliability, and ensure compliance with EMC standards.