Fluctuations in rolling bearing vibration signals, induced by stage-dependent degradation dynamics and stochastic disturbances under varying operating conditions, pose significant challenges for remaining useful life (RUL) prediction. Consequently, this nonstationarity masks subtle early degradation cues, hinders stage-transition modeling, and often causes purely data-driven methods to produce physically implausible RUL decay trajectories. Moreover, interpretability remains limited when learned degradation representations are weakly connected to physically meaningful decay dynamics. To overcome these challenges, a physics-informed temporal-enhancing neural network (PI-TENN) is developed for estimating the RUL of rolling bearings across multi-stage degradation regimes. Specifically, a temporal-enhancing degradation feature fusion module is constructed by coupling a multi-layer long short-term memory (LSTM) temporal dependency encoder with an attention-enhancing block. In this way, the multi-layer LSTM encoder captures long-range temporal dependency, while the attention-enhancing block suppresses noise-dominated time steps and highlights degradation-relevant patterns, thereby producing latent degradation representations that are stable across degradation stages. Furthermore, a universal partial differential equation (PDE) is constructed to explicitly relate the latent degradation representation to the decay rate of RUL, which enables the learning of stage-wise RUL evolution patterns across distinct degradation stages. Meanwhile, model optimization is guided by a data–physics fusion loss integrating data fitting, PDE residual, and monotonicity regularization, so that predictive accuracy and physically consistent stage-wise decay are jointly ensured. Finally, experiments on full-life-cycle steel and ceramic bearing datasets demonstrate improved accuracy, robustness under complex operating conditions, and enhanced physical consistency compared with representative baselines.
Connectivity probability is an important indicator of the planning, design, and evaluation of vehicle ad networks (VANET). As an important part of Intelligent Transportation System (ITS), VANET realizes the wide-scale sharing of information. It makes full use of the information, effectively reduces the occurrence of road traffic accidents, and greatly improves the traffic efficiency of roads in real life. This paper firstly summarizes the characteristics of VANET and the key parameter characteristics that affect its connectivity, and then classifies the system models of related literatures and introduces the various models. The connectivity probabilities of VANET under different system models are pointed out and analyzed. Finally, the connected probability features of different models are compared by simulation analysis.
During long-term operation, the accumulation of material damage in bearings leads to transitions in failure mechanisms, which are reflected by pronounced time-varying characteristics in vibration responses. Conventional single-model prediction approaches are inadequate to simultaneously capture the slow degradation behavior in the early stage and the rapid deterioration in the later stage. To address this issue, a multi-stage bearing performance degradation digital twin modeling framework based on ensemble support vector regression (SVR) is proposed. First, a five-degree-of-freedom bearing fault dynamic model is developed to generate simulated vibration signals, and the defect size over the entire bearing life cycle is inversely identified through bidirectional mapping between simulated and measured vibration signals. Subsequently, a dual-feature synergistically driven degradation stage partitioning strategy is proposed to divide the bearing degradation process into multiple stages. Based on the identified stages, an SVR model pool is constructed to establish stage-wise mapping relationships between bearing defect size and vibration features. Finally, the predicted defect sizes are fed back into the bearing fault dynamic model to generate updated simulated vibration signals, thereby forming a closed-loop iterative updating mechanism of the bearing digital twin. Both the XJTU-SY bearing dataset and a specially constructed dataset are employed to verify the proposed method, which demonstrates exceptional accuracy in lifecycle-wide degradation forecasting.
Scene monitoring and automatic interpretation in construction site scenarios play a crucial role. However, the changes in illumination and weather conditions of construction sites have a significant impact on the imaging quality of visual cameras. The effectiveness of existing semantic segmentation methods is extremely decreased without considering this problem. To solve this issue, we propose the multi-stage feature reconstructed semantic segmentation method for all-day monitor in construction sites. This method aims to improve the robustness against changes in the external environment. Specifically, the self-calibrated module (SCM) is adopted to reconstruct the input image and calculate the effective encoded features. SCM is embedded into the network for several stages to reconstruct multi-level features. Then, the higher-level features are aggregated and enhanced along the channel dimensions, which could obtain more context information. The higher-level is gradually combined with lower-level detailed features for decoding process. The images in construction sites are randomly augmented from different aspects, which could supervise the training process to achieve robust semantic segmentation with the supplement of image reconstruction. The qualitative and quantitative experiments show that compared with several state-of-the-art semantic segmentation methods, the proposed method could better adapt to changes in the environmental conditions and achieve all-day segmentation.