As a new type of fluorescent carbon nanomaterials, carbon quantum dots have been widely concerned in recent years because of their good biocompatibility, low cytotoxicity and easy surface functionalization. In this paper, nitrogen-doped carbon quantum dots (N-CQDs) were prepared by one-step hydrothermal method with citric acid as the carbon source and urea as a nitrogen source. The fluorescence spectrophotometer, Fourier infrared spectrometer, X-ray diffractometer, and transmission electron microscope were utilized to discover the luminescence properties, structural characteristics, morphology and size of the synthesized N-CQDs. The results showed that the best reaction conditions for preparing N-CQDs were as follows: the hydrothermal process parameters were 240 °C for 10 h, and the concentration of nitrogen doping was 0.6 wt%. Under these conditions, the prepared N-CQDs with bright blue fluorescence solution was uniform and stable. And the results showed the structural characteristics were weak crystalline graphite carbon, and the shape characteristics were nearly spherical quantum dot with about 5–10 nm diameters.
In this study, a novel polyurethane porous 3D scaffold based on polyethylene glycol (PEG) and polytetrahydrofuran glycol (PTMG) was developed by in situ polymerization and freeze drying. Aliphatic hexamethylene diisocyanate (HDI) as a nontoxic and safe agent was adopted to produce the rigid segment in polyurethane polymerization. The chemical structure, macrostructure, and morphology—as well as mechanical strength of the scaffolds—were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), and tensile tests. The results show that the HDI can react mildly with hydroxyl (–OH) groups of PEG and PTMG, while gas foaming action caused by the release of CO2 occurred simultaneously in the reactive process, resulting in a uniform porous structure of PU scaffold. Moreover, the scaffolds were soaked in water and freeze dried to obtain higher porosity and more interconnective microstructures. The scaffolds have a porosity of over 70% and pore size from 100 to 800 μm. The mechanical properties increased with increasing PEG content, while the hydrophilicity increased as well. After immersion in simulated body fluid (SBF), the scaffolds presented a stable surface structure. The gas foaming/freezing drying process is an excellent method to prepare skin tissue engineering scaffold from PTMG/PEG materials with high porosity and good inter connectivity.
As a new zero-optic luminescent material, carbon quantum points are widely focused and sustained, and many researchers are trying to use simple and fast methods and stable, good carbon sources to be prepared with a good fluorescent properties of carbon quantum dots. In this paper, carbon quantum dots were synthesized by solvothermal method with vanillin as carbon source, and the effects of solvothermal temperature and time on the luminescence properties of carbon quantum dots were explored. Then, carbon quantum dots were characterized by X-ray diffraction analysis, transmission electron microscopy analysis, infrared spectrum analysis, fluorescence spectrum analysis. Research results showed that ethanol solvent with vanillin as a carbon source by solvothermal method could synthesize good water soluble carbon quantum dots with weak crystallization, and its size was about 10 nm. This carbon quantum dots had obvious excitation wavelength dependence and produce blue light, which had potential application value in ion fluorescence probe or cell labeling.
Nanosized magnesium hydroxide (Mg(OH)2) with sheet and flower structure were prepared via precipitation reaction between magnesium chloride and alkaline precipitant, such as ammonium hydroxide, sodium hydroxide and urea. The structure and morphology of as-prepared samples were characterized through X-ray diffraction and scanning electron microscopy. Effect of precipitants and surface modifier on morphology and size of nano-Mg(OH)2 were investigated. Heat-resistance of Mg(OH)2 in polymer was discussed by thermogravimetry-differential thermal analysis. Mg(OH)2 nanostructure present superior morphology and heat-resistance with NH4OH-NaOH as precipitant and 3mol% acrylic acid as surface modifier.
Low-temperature boiling chlorination is the most common approach used to achieve a clean preparation of TiCl4 from ilmenite concentrates with high contents of calcium and magnesium impurities. However, this process did not systematically investigate the impact of the Ti/C ratio of the raw materials on the chlorination efficiency of Ti, Ca, and Mg elements. Thus, the influence of the carbon allocation proportion on the carbothermal reduction and boiling chlorination process of ilmenite concentrates with high contents of calcium and magnesium impurities was investigated in this study. The results show that the reduction products of ilmenite concentrates are mainly Mg-rich Ti2O3 impurities at a low carbon proportion. However, with increasing carbon proportion, Ti2O3 is gradually reduced to TiC x O1-x , and Mg2TiO4 appears. The Ti2O3 content in the acid-insoluble matter of the reduced products decreases after acid washing, while the TiC x O1-x content increases with increasing carbon allocation proportion. With increasing carbon proportion, the chlorination rate of the acid-insoluble matter increases, and the corresponding chlorination rates of titanium, magnesium, and calcium also increase. The residual carbon produced by acid-insoluble chlorination at high carbon proportions exacerbates the chlorination of Mg and Ca impurities.