Yongzhi Li

Dr. Yongzhi Li

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 August 2024 in Energy
Verified
Journal Article
Closed access
YLYongzhi Li
Yongzhi Li
MYMingfa Yao
Mingfa Yao
HLHeping Liang
Heping Liang
Haifeng LiuHaifeng Liu
Haifeng Liu
HWHu Wang
Hu Wang
ZZZhi Zhang
Zhi Zhang

29 June 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
Hao ChenHao Chen
Hao Chen
CWChenxi Wang
Chenxi Wang
XLXiang Li
Xiang Li
YLYongzhi Li
Yongzhi Li
MZMiao Zhang
Miao Zhang
Raouf MobasheriRaouf Mobasheri
Raouf Mobasheri
The climate change issue has become a growing concern due to the increasing greenhouse gas emissions. To achieve carbon neutrality for mitigating the climate problem, the oxy-fuel combustion (OFC) technique on internal combustion engines (ICEs) has attracted much attention. Furthermore, the water injection (WI) strategy was proven effective in improving the combustion process and thermal efficiency in engines under OFC mode. However, WI strategy effects on gasoline direct injection (GDI) engines fuelled with gasoline–alcohol blends have not been reported. This study quantitatively analysed WI mass and timing effects on oxy-fuel combustion performance from a GDI engine fuelled with E10 (10% ethanol and 90% gasoline in mass) by simulation. The results show that equivalent brake-specific fuel consumption (BSFCE) shows a monotonically decreasing trend with the increase in the water–fuel mass ratio (Rwf) from 0 to 0.2. However, further increasing Rwf would cause a deterioration in BSFCE due to the enhanced cooling effects of water vaporisation. Moreover, an appropriate water injection timing (tWI) could be explored for improving OFC performance, especially for large Rwf conditions. The difference in BSFCE between tWI = −100°CA and tWI = −60°CA can be up to around 6.3 g/kWh by increasing Rwf to 0.6.
1

15 January 2025 in Energies
Verified
Journal Article
Open access
PDF file
YLYongzhi Li
Yongzhi Li
ZZZhi Zhang
Zhi Zhang
Haifeng LiuHaifeng Liu
Haifeng Liu
WCWeide Chang
Weide Chang
ZSZanqiao Shu
Zanqiao Shu
MYMingfa Yao
Mingfa Yao
Methanol is a potential carbon-neutral fuel. It has a high latent heat of vaporization, making it difficult to achieve evaporation and mixing, and it is prone to forming a liquid film, which in turn affects engine performance. To reduce the liquid film and improve engine performance, this work investigates the influence mechanism of injection strategies on the generation of liquid films in the intake port and cylinder of an inline 6-cylinder port fuel injection (PFI) spark-ignition (SI) methanol engine and further explores the optimization scheme for improving engine performance. The results show that the end of injection (EOI) influences the methanol evaporation rate and the methanol–air mixing process, thereby determining the liquid film deposition, mixture distribution, and temperature distribution in the cylinder. As the EOI advances, the higher methanol evaporation rate during the intake process reduces the amount of methanol droplets and the deposition of a liquid film in the cylinder. The in-cylinder temperature is relatively high, while the mixture inhomogeneity slightly increases. As the EOI increases from 170 °CA to 360 °CA, the higher in-cylinder temperature and properly stratified mixture accelerate the early and middle stages of combustion, shorten the ignition delay, advance the center of combustion, and improve the brake thermal efficiency (BTE). However, further advancing the EOI results in the BTE remaining basically unchanged. Optimized injection timing can enhance the BTE by 1.4% to 2.4% under various load conditions. The increase in the EOI contributes to the reduction of HC emissions due to the weakening of the crevice effect with lower masses of methanol droplets and liquid film in the cylinder, while the increase in mixture inhomogeneity leads to an increase in CO emissions. In general, controlling the EOI at around 360 °CA can maintain relatively low CO emissions under various load conditions, while significantly reducing HC emissions by 71.2–76.4% and improving the BTE.