For the purpose of improving the productivity of laser metal deposition (LMD), the focus of current research is set on increasing the deposition rate, in order to develop high-deposition-rate LMD (HDR-LMD). The presented work studies the effects of the powder stream on HDR-LMD with Inconel 718. Experiments have been designed and conducted by using different powder feeding nozzles—a three-jet and a coaxial powder feeding nozzle—since the powder stream is mainly determined by the geometry of the powder feeding nozzle. After the deposition trials, metallographic analysis of the samples has been performed. The laser intensity distribution (LID) and the powder stream intensity distribution (PID) have been characterized, based on which the processes have been simulated. Finally, for verifying and correcting the used models for the simulation, the simulated results have been compared with the experimental results. Through the conducted work, suitable boundary conditions for simulating the process with different powder streams has been determined, and the effects of the powder stream on the process have also been determined. For a LMD process with a three-jet nozzle a substantial part of the powder particles that hit the melt pool surface are rebounded; for a LMD process with a coaxial nozzle almost all the particles are caught in the melt pool. This is due to the different particle velocities achieved with the two different nozzles. Moreover, the powder stream affects the heat exchange between the heated particles and the melt pool: a surface boundary condition applies for a powder stream with lower particle velocities, in the experiment provided by a three-jet nozzle, and a volumetric boundary condition applies for a powder stream with higher particle velocities, provided by a coaxial nozzle.

Laser Powder Bed Fusion (LPBF) of Ti-6Al-4V enables the manufacturing of complex parts for lightweight applications. The emerging microstructure in the LPBF process and thus the mechanical properties are defined by the thermal cycles, which are locally variable for complex geometries. Predictions of local mechanical properties by simulation would reduce the development time of new applications drastically but are today not possible on part scale, so new part applications must be qualified experimentally at great effort. In this study, representative geometry sections were transferred into a simplified sample shape to mechanically characterize different geometry-dependent microstructures. In areas exposed to comparatively increased heat input over time, a lamellar $\alpha$ + $\beta$ microstructure with $\beta$ fraction up to 20% was measured in contrast to the common martensitic ${\alpha }^{\prime }$ microstructure of LPBF-manufactured Ti-6Al-4V, resulting in reduced tensile strength and fatigue life. For the first time, a correlation was successfully established between ultimate tensile strength of multiple geometries and the corresponding temperature–time cycles. With reduced computational effort by use of simplifying assumptions in the simulation, this correlation model can theoretically be applied to the part level. This work has laid the foundation for the simulation-based prediction of mechanical properties for entire parts manufactured with LPBF.

Extreme high-speed laser material deposition, known by its German acronym EHLA, is a new variant of laser material deposition (LMD) with powdered additives. This variant’s process control is unlike that of LMD, where the powder melts as it contacts the melt pool. In the EHLA process, the laser beam melts the powder above the surface of the substrate to deliver a liquid to the melt pool. At a given intensity distribution in a laser beam, the heating of powder particles in the beam path depends largely on the three-dimensional powder particle density distribution (PDD) and the relative position within the laser beam caustic. As a key element of a comprehensive numerical process model for EHLA, this paper presents a statistical/numerical model of the powder-gas jet, as previously published in Experimentelle und modelltheoretische Untersuchungen zum Extremen Hochgeschwindigkeits-Laserauftragschweißen. The powder-gas jet is characterized experimentally and described with a mathematical model. This serves to map the PDD of the powder-gas flow—and particularly the particle trajectories for different grain fractions—as well as the powder mass flows and carrier and inert gas settings, to a theoretical model. The result is a numerical description of the particle trajectories that takes into account the measured particle size distribution with calculations made on the assumption of a constant particle velocity and linear trajectories of the particles.

Aluminum-magnesium-scandium-zirconium (AlMgScZr) alloys need to be rapidly cooled from the liquid state to obtain a high degree of solute supersaturation that helps to exploit the precipitation hardening potential of the material. While AlMgScZr alloys have been successfully used in laser powder bed fusion (LPBF) processes, there has been little research in the field of laser directed energy deposition (DED) of the material. The limited previous studies have shown that the performance of AlMgScZr parts fabricated with DED only reached about 60% of that of the parts fabricated with LPBF. In view of breaking through the limitation associated with the process conditions of conventional DED, this work demonstrates the DED of AlMgScZr alloys in high-speed process regimes and elucidates the mechanism of enhancing the hardness and tensile strength of AlMgScZr alloys by increasing the cooling rate by one to two orders of magnitudes, as well as reducing the track overlapping and the porosity of the specimens during the process. A maximum average hardness of nearly 150 HV0.1 and a max. tensile strength of 407 MPa are obtained by using an energy per unit length of 5400 J/m and a powder feed rate per unit length of 0.25 g/m.

This article presents an investigation of the convection behavior of the melt pool for laser surface alloying with a wide beam. A line beam source with a dimension of 6 mm × 0.7 mm from a 3 kW cw Nd–YAG laser was used. The work concentrated on studies of the influence of various laser operating conditions, especially the melt width of the tracks and the substrate thermal properties, on the convection behavior during the laser surface alloying process. Three different substrates precoated with a Ni layer were selected on the basis of their different thermal properties. An investigation of the relationships between the laser beam dimension, the structure of melt flow, and concentration fields of the alloying elements was carried out. It was found that the beam width had a significant effect on the alloying patterns on solidification. It was also found that a wider beam width (varied with a mask aperture) produced a greater melt depth. A three-dimensional mathematical model was applied to numerically simulate the temperature field and convection flow of the melt pool. Some specific alloying patterns were found favorable for coinage applications.