Laser Powder Bed Fusion (LPBF) of Ti-6Al-4V enables the manufacturing of complex parts for lightweight applications. The emerging microstructure in the LPBF process and thus the mechanical properties are defined by the thermal cycles, which are locally variable for complex geometries. Predictions of local mechanical properties by simulation would reduce the development time of new applications drastically but are today not possible on part scale, so new part applications must be qualified experimentally at great effort. In this study, representative geometry sections were transferred into a simplified sample shape to mechanically characterize different geometry-dependent microstructures. In areas exposed to comparatively increased heat input over time, a lamellar $\alpha$ + $\beta$ microstructure with $\beta$ fraction up to 20% was measured in contrast to the common martensitic ${\alpha }^{\prime }$ microstructure of LPBF-manufactured Ti-6Al-4V, resulting in reduced tensile strength and fatigue life. For the first time, a correlation was successfully established between ultimate tensile strength of multiple geometries and the corresponding temperature–time cycles. With reduced computational effort by use of simplifying assumptions in the simulation, this correlation model can theoretically be applied to the part level. This work has laid the foundation for the simulation-based prediction of mechanical properties for entire parts manufactured with LPBF.

Extreme high-speed laser material deposition, known by its German acronym EHLA, is a new variant of laser material deposition (LMD) with powdered additives. This variant’s process control is unlike that of LMD, where the powder melts as it contacts the melt pool. In the EHLA process, the laser beam melts the powder above the surface of the substrate to deliver a liquid to the melt pool. At a given intensity distribution in a laser beam, the heating of powder particles in the beam path depends largely on the three-dimensional powder particle density distribution (PDD) and the relative position within the laser beam caustic. As a key element of a comprehensive numerical process model for EHLA, this paper presents a statistical/numerical model of the powder-gas jet, as previously published in Experimentelle und modelltheoretische Untersuchungen zum Extremen Hochgeschwindigkeits-Laserauftragschweißen. The powder-gas jet is characterized experimentally and described with a mathematical model. This serves to map the PDD of the powder-gas flow—and particularly the particle trajectories for different grain fractions—as well as the powder mass flows and carrier and inert gas settings, to a theoretical model. The result is a numerical description of the particle trajectories that takes into account the measured particle size distribution with calculations made on the assumption of a constant particle velocity and linear trajectories of the particles.

Aluminum-magnesium-scandium-zirconium (AlMgScZr) alloys need to be rapidly cooled from the liquid state to obtain a high degree of solute supersaturation that helps to exploit the precipitation hardening potential of the material. While AlMgScZr alloys have been successfully used in laser powder bed fusion (LPBF) processes, there has been little research in the field of laser directed energy deposition (DED) of the material. The limited previous studies have shown that the performance of AlMgScZr parts fabricated with DED only reached about 60% of that of the parts fabricated with LPBF. In view of breaking through the limitation associated with the process conditions of conventional DED, this work demonstrates the DED of AlMgScZr alloys in high-speed process regimes and elucidates the mechanism of enhancing the hardness and tensile strength of AlMgScZr alloys by increasing the cooling rate by one to two orders of magnitudes, as well as reducing the track overlapping and the porosity of the specimens during the process. A maximum average hardness of nearly 150 HV0.1 and a max. tensile strength of 407 MPa are obtained by using an energy per unit length of 5400 J/m and a powder feed rate per unit length of 0.25 g/m.

In the present study, we propose a hybrid manufacturing route to produce high-quality Ti6Al4V parts, combining additive powder laser directed energy deposition (L-DED) for manufacturing of preforms, with subsequent hot forging as a thermomechanical processing (TMP) step. After L-DED, the material was hot formed at two different temperatures (930 °C and 1070 °C) and subsequently heat-treated for stress relief annealing. Tensile tests were performed on small sub-samples, taking into account different sample orientations with respect to the L-DED build direction and resulting in very good tensile strengths and ductility properties, similar or superior to the forged material. The resulting microstructure consists of very fine grained, partially globularized alpha grains, with a mean diameter ~0.8–2.3 µm, within a beta phase matrix, constituting between 2 and 9% of the sample. After forging in the sub-beta transus temperature range, the typical L-DED microstructure was no longer discernible and the anisotropy in tensile properties, common in additive manufacturing (AM), was significantly reduced. However, forging in the super-beta transus temperature range resulted in remaining anisotropies in the mechanical properties as well as an inferior tensile strength and ductility of the material. It was shown, that by combining L-DED with thermomechanical processing in the sub-beta transus temperature range of Ti6Al4V, a suitable microstructure and desirable mechanical properties for many applications can be obtained, with the advantage of reducing the material waste.

The X-ray phase contrast imaging is a powerful method to understand the fundamental behavior of the melt and keyhole during the laser beam welding process. In this paper, the keyhole-induced vapor capillary formation in the melt pool is investigated by using an adjustable laser beam source. For this purpose, the aluminum A1050 specimen with a thickness of 0.5 mm is molten only with the heat conduction welding regime by using the ring-mode laser beam. Once the specimen is molten through, the core multi-mode laser beam is then applied to vaporize the melt and a transition to keyhole welding regime occurs. Therefore, the core multi-mode laser beam with an intensity value of 33.3 MW/cm² is investigated. The correlation between the keyhole-induced vapor capillary and the melt behavior is further investigated in this paper which was recorded with a high sampling rate of 19 kHz. In addition, a theoretical calculation about the keyhole depth is discussed in this paper.

Laser material deposition (LMD) is a widely used coating process in industry. However, to increase its economic appeal, higher process speeds are required. The solution to this challenge is an innovative modification known as extreme high-speed laser material deposition (EHLA). EHLA allows for an impressive increase in process speed from 2 m/min for conventional LMD to 500 m/min. With the ability to adjust process parameters, EHLA can generate tailor-made surface properties, expanding its potential application beyond current industrial uses. In this novel study, we explore the effects of relative positioning between tools (laser beam and powder–gas jet) and substrate on the surface properties of EHLA coatings. By laterally and axially offsetting the tools, the proportional energy coupling of the laser radiation into the powder–gas jet and substrate can be modified. Altering the position of the powder–gas jet can also affect the weld pool flow or number of particle attachments, thereby affecting surface properties. This approach allows for the adjustment of surface roughness over a wide range—from smooth, quasi-laser-polished surfaces to rough surfaces covered with particle adhesions.