Growth dynamics of thin-films involves both shadowing and re-emission effects. Shadowing can originate from obliquely incident atoms being preferentially deposited on hills of the surface, which leads to a long range geometrical effect, as well as from an atomic shadowing process that can occur even during normal angle deposition. Re-emission effect is a result of nonsticking atoms, which can bounce off from hills and deposit on valleys of the surface. In the case of an energetic incident flux, re-emission can also originate from a resputtering process that includes a surface atom being knocked off by an incident ion/atom followed by redeposition to another surface point. Due to their long-range nonlocal nature, both the shadowing effect (which tries to roughen the surface) and re-emission effect (which has a smoothening effect) have been shown to be more dominant over local effects such as surface diffusion, and have been proven to be critical processes in accurately determining the dynamic evolution of surface roughness. Recent Monte Carlo simulation methods that involve shadowing, re-emission, surface diffusion, and noise effects successfully predicted many experimentally relevant surface roughness evolution results reported in the literature. For example, root-mean-square surface roughness (ω) of Monte Carlo simulated thin-films have evolved with time t according to a power law behavior ω ∼ tβ, with β values ranging from about 0 to 1 for a growth with strong re-emission effects (i.e., low sticking coefficients) and a growth with dominant shadowing effects (i.e., with high sticking coefficients), respectively. Potential future thin-film growth modeling studies are also discussed. These include advanced simulation approaches that can incorporate atomistic details of physical and chemical processes and a recently developed network growth model that can potentially capture some universal aspects of thin-film growth dynamics independent of the details of growth process.
Surfaces with metal oxide nanostructures have gained considerable interest in applications such as sensors, detectors, energy harvesting cells, and batteries. However, conventional fabrication techniques suffer from challenges that hinder wide and effective applications of such surfaces. Most of the metal oxide nanostructure synthesis methods are costly, complicated, non-scalable, environmentally hazardous, or applicable to only certain few materials. Therefore, it is crucial to develop a simple metal oxide nanostructure fabrication method that can overcome all these limitations and pave the way to the industrial application of such surfaces. Here, we demonstrate that a wide variety of metals can form metal oxide nanostructures on their surfaces after simply interacting with hot water. This method, what we call hot water treatment, offers the ability to grow metal oxide nanostructures on most of the metals in the periodic table, their compounds, or alloys by a one-step, scalable, low-cost, and eco-friendly process. In addition, our findings reveal that a “plugging” mechanism along with surface diffusion is critical in the formation of such nanostructures. This work is believed to be of importance especially for researchers working on the growth of metal oxide nanostructures and their application in functional devices.
The dynamic roughening of amorphous silicon nitride growth front prepared by a plasma-enhanced chemical vapor deposition is presented. Morphology of the films grown at different substrate temperatures (from 50 to 350 °C) for various lengths of deposition time was measured ex situ using atomic force microscopy. The dynamic scaling exponents are measured as and and do not change significantly under the investigated substrate temperature range. An attempt has been made to describe the plasma growth process using a multiparticle reemission model where the incident flux distribution, sticking coefficient, shadowing, surface diffusion, and desorption mechanisms all contributed to the growing morphology.
6 June 2017 in The International Journal of Advanced Manufacturing Technology
We present a network modeling approach for various thin film growth techniques that incorporates re-emitted particles due to the nonunity sticking coefficients. We model re-emission of a particle from one surface site to another one as a network link and generate a network model corresponding to the thin film growth. Monte Carlo simulations are used to grow films and dynamically track the trajectories of re-emitted particles. We performed simulations for normal incidence, oblique angle, and chemical vapor deposition (CVD) techniques. Each deposition method leads to a different dynamic evolution of surface morphology due to different sticking coefficients involved and different strength of shadowing effect originating from the obliquely incident particles. Traditional dynamic-scaling analysis on surface morphology cannot point to any universal behavior. On the other hand, our detailed network analysis reveals that there exist universal behaviors in degree distributions, weighted average degree versus degree, and distance distributions independent of the sticking coefficient used and sometimes even independent of the growth technique. We also observe that network traffic during high-sticking coefficient CVD and oblique-angle deposition occurs mainly among edges of the columnar structures formed while it is more uniform and short range among hills and valleys of small sticking coefficient CVD and normal-angle depositions that produce smoother surfaces.