Maria Jose Quintana

Dr. Maria Jose Quintana

orcid

Research Focus & Metrics

Academic Career Length

27Years (2000-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 July 2024 in Materials
Verified
Journal Article
Open access
PDF file
RHRAJIB HALDER
RAJIB HALDER
Petrus Christiaan PistoriusPetrus Christiaan Pistorius
Petrus Christiaan Pistorius
SBScott Blazanin
Scott Blazanin
RSRigved P. Sardey
Rigved P. Sardey
MQMaria Jose Quintana
Maria Jose Quintana
ARAnthony D. Rollett
Anthony D. Rollett
Laser hot wire directed energy deposition (LHW-DED) is a layer-by-layer additive manufacturing technique that permits the fabrication of large-scale Ti-6Al-4V (Ti64) components with a high deposition rate and has gained traction in the aerospace sector in recent years. However, one of the major challenges in LHW-DED Ti64 is heat accumulation, which affects the part quality, microstructure, and properties of as-built specimens. These issues require a comprehensive understanding of the layerwise heat-accumulation-driven process–structure–property relationship in as-deposited samples. In this study, a systematic investigation was performed by fabricating three Ti-6Al-4V single-wall specimens with distinct interlayer delays, i.e., 0, 120, and 300 s. The real-time acquisition of high-fidelity thermal data and high-resolution melt pool images were utilized to demonstrate a direct correlation between layerwise heat accumulation and melt pool dimensions. The results revealed that the maximum heat buildup temperature of the topmost layer decreased from 660 °C to 263 °C with an increase to a 300 s interlayer delay, allowing for better control of the melt pool dimensions, which then resulted in improved part accuracy. Furthermore, the investigation of the location-specific composition, microstructure, and mechanical properties demonstrated that heat buildup resulted in the coarsening of microstructures and, consequently, the reduction of micro-hardness with increasing height. Extending the delay by 120 s resulted in a 5% improvement in the mechanical properties, including an increase in the yield strength from 817 MPa to 859 MPa and the ultimate tensile strength from 914 MPa to 959 MPa. Cooling rates estimated at 900 °C using a one-dimensional thermal model based on a numerical method allowed us to establish the process–structure–property relationship for the wall specimens. The study provides deeper insight into the effect of heat buildup in LHW-DED and serves as a guide for tailoring the properties of as-deposited specimens by regulating interlayer delay.

5 July 2022 in Integrating Materials and Manufacturing Innovation
Verified
Journal Article
Open access
PDF file
MQMaria Jose Quintana
Maria Jose Quintana
ATAndrew J. Temple
Andrew J. Temple
DHD. Gary Harlow
D. Gary Harlow
PCPeter C. Collins
Peter C. Collins
In this paper, phenomenological relationships are presented that permit the prediction of the plastic regime of stress–strain curves using a limited number of parameters. These relationships were obtained from both conventional (wrought + β annealed) and additively manufactured (i.e., “3D printed”) Ti-6Al-4V. Three different methods of additive manufacturing have been exploited to produce the materials, including large-volume electron beam additive manufacturing, large-volume laser hot wire additive manufacturing, and small-volume selective laser melting. The general fundamental expressions are independent not only of the additive manufacturing process, but also of a wide variety of post-deposition heat treatments, however the coefficients are specific to material states. Thus, this work demonstrates that it is possible to predict not only the ultimate tensile strength, but also the full true stress, true strain curves, if certain parameters of the material are known. In general, the prediction of ultimate tensile strength are within 5% of the experimentally measured values across all additive manufacturing variants and subsequent heat treatments. The absolute values of ultimate tensile strength range from ~ 910 MPa to ~ 1170 MPa for the single alloy Ti-6Al-4V. Data representing 113 explicit samples are included in this work.

29 November 2024 in Materials
Verified
Journal Article
Open access
PDF file
GJGrant Johnson
Grant Johnson
MDMatthew M Dolde
Matthew M Dolde
JZJonathan T Zaugg
Jonathan T Zaugg
MQMaria Jose Quintana
Maria Jose Quintana
PCPeter C. Collins
Peter C. Collins
Despite the significant advances made involving the additive manufacturing (AM) of metals, including those related to both materials and processes, challenges remain in regard to the rapid qualification and insertion of such materials into applications. In general, understanding the process–microstructure–property interrelationships is essential. To successfully understand these interrelationships on a process-by-process basis and exploit such knowledge in practice, leveraging monitoring, modeling, and statistical analysis is necessary. Monitoring allows for the identification and measurement of parameters and features associated with important physical processes that may vary spatially and temporally during the AM processes that will influence part properties, including spatial variations within a single part and part-to-part variability, and, ultimately, quality. Modeling allows for the prediction of physical processes, material states, and properties of future builds by creating material state abstractions that can then be tested or evolved virtually. Statistical analysis permits the data from monitoring to inform modeling, and vice versa, under the added consideration that physical measurements and mathematical abstractions contain uncertainties. Throughout this review, the feedstock, energy source, melt pool, defects, compositional distribution, microstructure, texture, residual stresses, and mechanical properties are examined from the points of view of monitoring, modeling, and statistical analysis. As with most active research subjects, there remain both possibilities and limitations, and these will be considered and discussed as appropriate.


1 October 2010 in Journal of Iron and Steel Research International
Verified
Journal Article
Closed access
RGR. González
R. González
JGJ. O. García
J. O. García
MBM. A. Barbés
M. A. Barbés
MQMaria Jose Quintana
Maria Jose Quintana
LVL. F. Verdeja
L. F. Verdeja
JVJ. I. Verdeja
J. I. Verdeja

27 August 2023 in Journal of Materials Science
Verified
Journal Article
Open access
PDF file
KOKatie O'Donnell
Katie O'Donnell
MQMaria Jose Quintana
Maria Jose Quintana
MKMatthew J. Kenney
Matthew J. Kenney
PCPeter C. Collins
Peter C. Collins
Defects in parts produced by additive manufacturing, instead of simply being perceived as deleterious, can act as important sources of information associated with the complex physical processes that occur during materials deposition and subsequent thermal cycles. Indeed, they act as materials-state ‘fossil’ records of the dynamic AM process. The approach of using defects as epoch-like records of prior history has been developed while studying additively manufactured Ti–6Al–4V and has given new insights into processes that may otherwise remain either obscured or unquantified. Analogous to ‘epochs,’ the evolution of these defects often is characterized by physics that span across a temporal length scale. To demonstrate this approach, a broad range of analyses including optical and electron microscopy, X-ray computed tomography, energy-dispersive spectroscopy, and electron backscatter diffraction have been used to characterize a raster-scanned electron beam Ti–6Al–4V sample. These analysis techniques provide key characteristics of defects such as their morphology, location within the part, complex compositional fields interacting with the defects, and structures on the free surfaces of defects. Observed defects have been classified as banding, spherical porosity, and lack of fusion. Banding is directly related to preferential evaporation of Al, which has an influence on mechanical properties. Lack-of-fusion defects can be used to understand columnar grain growth, fluid flow of melt pools, humping, and spattering events. Graphical abstract