Yuehui He

Yuehui He


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 August 2012 in Macromolecules
Verified
Journal Article
Closed access
BLBo Liu
Bo Liu
XCXuewen Chen
Xuewen Chen
YZYINGPING ZOU
YINGPING ZOU
LXLu Xiao
Lu Xiao
XXXinjun Xu
Xinjun Xu
JSJinjun Shao
Jinjun Shao

1 February 2014 in Transactions of Nonferrous Metals Society of China
Verified
Journal Article
Closed access
QWQi-Gang Weng
Qi-Gang Weng
Ruidi LiRuidi Li
Ruidi Li
TYTie-Chui Yuan
Tie-Chui Yuan
JLJian Li
Jian Li
Yuehui HeYuehui He
Yuehui He

19 September 2018 in Royal Society Open Science
Verified
Journal Article
Open access
DHDong Hongxing
Dong Hongxing
QLQiuping Liu
Qiuping Liu
Yuehui HeYuehui He
Yuehui He
A nanoporous BiVO 4 /TiO 2 /Ti film was successfully fabricated by electrodepositing a nanoporous BiOI film on nanoporous TiO 2 arrays followed by annealing at 450°C for 2 h. The electrodeposition of BiOI film was carried out at different times (10, 30, 100, 500 and 1000 s) in Bi(NO 3 ) 3 and KI solution. The morphological, crystallographic and photoelectrochemical properties of the prepared BiVO 4 /TiO 2 /Ti heterojunction film were examined by using different characterization techniques. UV–vis spectrum absorption studies confirmed an increase in absorption intensities with increasing electrodeposition time, and the band gap of BiVO 4 /TiO 2 /Ti film is lower than that of TiO 2 /Ti. The photocatalytic efficiency of BiVO 4 /TiO 2 /Ti heterojunction film was higher compared to that of the TiO 2 /Ti film owing to the longer transient decay time for BiVO 4 /TiO 2 /Ti film (3.2 s) than that of TiO 2 /Ti film (0.95 s) in our experiment. The BiVO 4 /TiO 2 /Ti heterojunction film prepared by electrodeposition for 1000 s followed by annealing showed a high photocurrent density of 0.3363 mA cm −2 at 0.6 V versus saturated calomel electrode. Furthermore, the lowest charge transfer resistance from electrochemical impedance spectroscopy was recorded for the BiVO 4 /TiO 2 /Ti film (1000 s) under irradiation.

15 September 2017 in Materials
Verified
Journal Article
Open access
PDF file
LNLin Nan
Lin Nan
Yuehui HeYuehui He
Yuehui He
XKXiyue Kang
Xiyue Kang
In this paper, the influence of the extra solid phase reaction on the interface structure and mechanical properties of titanium carbonitride-based cermets were investigated. The extra solid phase reaction in the preparation process of cermets could induce the formation of a core/rim/binder interface with the coherent structure and reinforce the interface bonding strength in cermets. The existence of a coherent structure interface can inhibit crack spread and improve the toughness and abrasion resistance of titanium carbonitride-based cermets significantly. Cermets can exhibit the high hardness Rockwell Hardness A (HRA) 92.3, fracture toughness of 11.6 MPa·m1/2, and transverse rupture strength of 2810 MPa.

2 February 2020 in Crystals
Verified
Journal Article
Open access
PDF file
YJYao Jiang
Yao Jiang
XLXinli Liu
Xinli Liu
HGHaiyan Gao
Haiyan Gao
Yuehui HeYuehui He
Yuehui He
Reactively synthesized porous Ti3SiC2 with different pore sizes was prepared using TiH2, Si and graphite powders as starting materials. The effect of pore size on the flexural stress–strain relationship, bending strength and flexural elastic modulus were investigated. The results show that the synthesized porous Ti3SiC2 intermetallic compounds have a characteristic of a high-purity MAX phase with typical laminate microstructure. When the average pore size decreases from 21.8 to 2.1 μm, the volume content of Ti3SiC2 phase ranges from 96.9% to 99.6%, and the porosity is in the range of 49.9% to 54.1%. The flexural stress–strain curves of porous Ti3SiC2 show a characteristic of two stages of elastic deformation and fracture. The flexural modulus is in the range of 13 to 70 GPa, which increases rapidly with further decrease of the pore size. A relation similar to the Hall–Petch equation between the mechanical property and the pore size was investigated for the porous material.

3 June 2024 in Chemengineering
Verified
Journal Article
Open access
PDF file
XTXiaowei Tang
Xiaowei Tang
Yuehui HeYuehui He
Yuehui He
The usage of copper (Cu) ores containing low or no arsenic (As) has reduced, and Cu ores containing high levels of As have emerged as vital mineral resources for Cu extraction and processing. The quality of the Cu ores has decreased from 1.6% to approximately 1.0%. The proportion of As to Cu in 15% of Cu resources currently reaches 1:5. However, during the extraction and processing of Cu ores, As presents significant environmental harm. Hence, safely and effectively removing As is paramount in Cu smelting and processing, holding substantial importance in fostering environmentally sustainable practices within the Cu extraction and processing industry. This article consolidates the resource distribution of As-containing Cu (ACC) ores, comprehensively and systematically evaluates the present advancements in extracting techniques for these minerals, and identifies the challenges inherent in pyrometallurgical and wet processes for treating ACC deposits. Pyrometallurgy is a simple primary roasting technique and has widespread applicability in the treatment of various ACC minerals. Its disadvantages are the emission of exhaust gas and the high treatment costs associated with it. The wet arsenic removal method boasts advantages including minimal air pollution and a high resource recovery rate, significantly aiding in Cu concentrate recovery; its major drawback is the production of As-containing wastewater. The hydrometallurgical removal of As from ACC mines involves extracting As through leaching. Recently, biometallurgy has presented innovative solutions using specialized microorganisms to bioleach or bioabsorb As, but large-scale industrial applications still lack specific practical implementation. This review explores the underlying causes of the challenges encountered in processing ACC minerals. Additionally, it highlights pyrometallurgical roasting coupled with high-temperature filtration as a pivotal advancement in the extraction and processing of ACC ores.