Abdulrahman AlGhamdi

Dr. Abdulrahman AlGhamdi

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 May 2024 in Polymers
Verified
Journal Article
Open access
PDF file
AAAbdulrahman AlGhamdi
Abdulrahman AlGhamdi
SASamaher Hamed Athamh
Samaher Hamed Athamh
RAReham Ahmad Alzahrani
Reham Ahmad Alzahrani
HFHanan Filemban
Hanan Filemban
Objectives: The aim of this study is to assess the micro-tensile bond strength and the mode of failure of a bioactive hybrid self-adhesive composite (Surefil one) under various dentin conditions. Methods: Thirty-two extracted human molar teeth were used to test the micro-tensile bond strength of Surefil one under different dentine conditions (no treatment, 37% phosphoric acid etching, and universal adhesive) in comparison with a resin-modified glass ionomer (RIVA). All restorations were light cure-bonded onto flat dentine and then sectioned into beams. Then, fractured specimens were observed under a light microscope to evaluate the mode of failure. Results: The Surefil one no-treatment group (NTG) exhibited the highest micro-tensile bond strength. Furthermore, there was no statistically significant difference observed between the Surefil one adhesive group (EAG) and the Surefil one acid etch group (EG). However, compared to other groups, the resin-modified glass ionomer (RIVA) produced the lowest results, which are statistically significant. Conclusion: Surefil one offers superior bond strength values when compared to resin-modified glass ionomers. Furthermore, Surefil one requires no dentin condition and has more straightforward clinical steps.

26 March 2026 in Journal of Esthetic and Restorative Dentistry
Verified
Journal Article
Open access
AAAbdulrahman AlGhamdi
Abdulrahman AlGhamdi
HFHanan Filemban
Hanan Filemban
Objective: To evaluate the influence of different polishing systems on the surface roughness and gloss of two nano‐filled resin composites, and to investigate the effect of a modeling agent (Ceramage) on surface roughness. Methods: Two nano‐filled resin composites, Filtek Z350 XT and Palfique LX5, were used. Composite discs (8 mm diameter, 3 mm depth) were fabricated, and four polishing systems, Super Snap X‐Treme, Diacomp Plus Twist, OptraGloss, and Enhance, were used. Polishing was performed by a trained operator at controlled speed and pressure. After polishing, the Ceramage modeling agent was applied on the surface using a #4 universal brush. Surface roughness (Ra) was measured with a 3D optical microscope using vertical scanning interferometry, and gloss (GU) was measured with a gloss meter at a 60° angle. Surface roughness measurements were taken before and after application of the Ceramage modeling agent. Two‐way ANOVA was used to evaluate the effects of composite type and polishing system on surface roughness and gloss, followed by Tukey's HSD post hoc tests. A paired‐samples t ‐test was used to compare roughness values before and after modeling agent application. Statistical significance was set at p < 0.05. Results: Both composite type and polishing system significantly affected surface roughness and gloss ( p < 0.001). Overall, Filtek Z350 XT exhibited lower surface roughness and higher gloss than Palfique LX5 across all polishing protocols. OptraGloss and Diacomp Plus Twist produced the smoothest surfaces and highest gloss, whereas Enhance and Super Snap X‐Treme yielded rougher surfaces and lower gloss. In addition, the application of the Ceramage modeling agent significantly reduced surface roughness in all groups ( p < 0.001), with the most pronounced effect in specimens polished with the rougher systems (Enhance and Super Snap X‐Treme). Conclusion: The type of nano‐filled composite and polishing system substantially influences surface roughness and gloss. OptraGloss and Diacomp Plus Twist deliver superior surface quality, whereas Enhance and Super Snap X‐Treme yield less favorable results. The Ceramage modeling agent effectively reduces surface roughness, particularly after rough polishing protocols. Tailoring polishing protocols to specific composite materials is essential to optimize esthetic and functional outcomes. Further clinical studies are warranted to validate these findings under intraoral conditions

25 September 2025 in European Journal of Dental Education
Verified
Journal Article
Closed access
Afnan O. Al-ZainAfnan O. Al-Zain
Afnan O. Al-Zain
AAAbdulrahman AlGhamdi
Abdulrahman AlGhamdi
BABashair Alansari
Bashair Alansari
AAAlanoud Alamoudi
Alanoud Alamoudi
HEHeba El‐Deeb
Heba El‐Deeb
EIEman H. Ismail
Eman H. Ismail