Ummi Kultsum

Ms. Ummi Kultsum

orcid

Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 February 2024 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
UKUmmi Kultsum
Ummi Kultsum
ASAndi Ibrahim Soumi
Andi Ibrahim Soumi
ABAnanta Baharudin
Ananta Baharudin
PMPutra Dwi Manunggal
Putra Dwi Manunggal
This study investigates the performance of a four-stroke, spark-ignition engine equipped with a commercial HHO generator that utilizes tap water for HHO gas production. Employing adjustable voltage levels (15 V, 25 V, and 30 V), the generator’s impact on engine performance was assessed through experimental dyno tests, measuring torque, power, and fuel consumption, complemented by numerical analyses of HHO production and thermal efficiency. The results, comparing engine operation with and without the HHO system, aim to evaluate the HHO generator’s effectiveness as a fuel supplement for enhancing engine performance.

27 January 2025 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
UKUmmi Kultsum
Ummi Kultsum
CACahyo Jawoto Anggoro
Cahyo Jawoto Anggoro
DMDewi Mahyunani
Dewi Mahyunani
ASAndi Ibrahim Soumi
Andi Ibrahim Soumi
Hydrogen generated through electrolysis is a feasible, sustainable energy source. HHO gas, a combination of hydrogen and oxygen generated via water electrolysis, is a clean and efficient energy source. The influence of NaOH electrolyte concentrations (2%, 4%, 6%, 8%, and 10%) and electrode plate numbers (2, 4, and 6) on HHO gas production and hydrostatic pressure will be examined in this study. Both NaOH concentration and electrode plate number increase HHO gas generation and hydrostatic pressure. A 10% NaOH concentration with six plates produced the most pressure and highest rate of hydrogen production.

28 February 2024 in Engineering Proceedings
Verified
Conference Paper
Open access
PDF file
AHAgus Hariyanto
Agus Hariyanto
Agus Dwi AnggonoAgus Dwi Anggono
Agus Dwi Anggono
DPDessy Ade Pratiwi
Dessy Ade Pratiwi
AAAnas Bariquddin Amali
Anas Bariquddin Amali
SMSekar Melaty
Sekar Melaty
UKUmmi Kultsum
Ummi Kultsum
This research aims to determine the effect of the volume fraction of coconut shell composite, with an epoxy matrix at 10% coconut shell water content, on the composite’s tensile strength, impact, density, and fracture results with the macrostructure. The materials used to make this composite are coconut shell particles, with a diameter of 1mm at a water content of 10%, and epoxy matrix and hardener, in a ratio of 1:1. Variations in volume fraction are 10%, 20%, 30%, 40% and 50%. The composite was manufactured using a press mold. Composite testing was in accordance with ASTM standards for tensile testing, using ASTM D 638-02 and impact testing using ASTM D 256-00. Macro photo results that determine the type of fracture that occurred were taken of the fracture resulting from tensile and impact tests. The test results showed that the highest tensile strength was at a volume fraction of 40% of 21.59 MPa, and the lowest was at 10% of 7.15 MPa. The highest impact value was shown in a composite with a volume fraction of 50% of 0.074 J/mm2, and the lowest had a volume fraction of 10% of 0.010 J/mm2. The highest density was a composite with a volume fraction of 50% of 1.067 gr/cm3, and the lowest had a volume fraction of 10% of 1.014 gr/cm3. In observing the fracture after tensile and impact testing, it can be seen that the fracture was brittle, and the direction of crack propagation is perpendicular to the direction of the tensile stress that is acting to produce a relatively flat fracture surface.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
MPMuttaqin Rahmat Pangaribawa
Muttaqin Rahmat Pangaribawa
PPPramuko Ilmu Purboputo
Pramuko Ilmu Purboputo
BWBachtiar Fajar Wicaksono
Bachtiar Fajar Wicaksono
ADAgung Setyo Darmawan
Agung Setyo Darmawan
BSBibit Sugito
Bibit Sugito
NINur Annisa Istiqamah
Nur Annisa Istiqamah
Metal is an essential substance in the industrial world for supporting human life and technological advancement. Shaping and increasing metal’s ability involves the heat treatment process. This research aims to see how the microstructure and hardness of metal change after being heat treated with quenching and tempering medium at room temperature and ice. The experiment was conducted utilizing a heat treatment process involving heating the material to 840°C for 60 minutes, then quenching it with water and ice and tempering it at 200°C for 20 minutes. The hardness test employs the Rockwell Hardness Test method, which uses a 9-point hardness scale with the primary load (P) of 150kg-f. The observations for the micro test were in the form of density variations in ferrite, pearlite, and martensite crystal grains. Microstructure investigations showed the presence of martensite in the material after being heat-treated. The hardness test showed that the carbon steel material experienced a decrease in hardness from the initial value of 43.12 HRC to 39.32 HRC and 38.14 HRC after quenching water and ice water. The comparison of tempering has no significant effect on hardness with values of 40.63 HRC and 38.94 HRC tempering followed by water-quenching and ice water-quenching, respectively.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
PPPatna Partono
Patna Partono
DPDian Angga Prakoso
Dian Angga Prakoso
MAMasyrukan
Masyrukan
SWSunardi Wiyono
Sunardi Wiyono
DPDessy Ade Pratiwi
Dessy Ade Pratiwi
Desi GustianiDesi Gustiani
Desi Gustiani
This study examines the density, porosity, microstructure, and hardness of aluminum raw materials from used pistons using gravity dies casting and gravity investment casting processes. Gravity die casting and gravity investment casting at a casting temperature of 750°C were employed in this research. Emission Spectrometry is used to determine the chemical composition of a substance (ASTM E-1251). Porosity was measured using macro photography and a digital microscope, with the findings of each mold temperature fluctuation compared. The Rockwell hardness tester is used to determine the hardness of a material (ASTM E-384). A metallographic microscope was used to examine the microstructure of the castings (ASTM E3-11). According to ASTM B-85 standards, this material comprises 71.05% (Al) composition, 13.65% (Si), 7.178% (Cu), 3.4508% (Fe), 1.7870% (Zn), and additional components up to 100%, and is categorized as Aluminum Al-Si (Aluminum-Silicon)A413.0. The density of the test object was calculated using gravity die casting at 2.6972 gr/cm3 and gravity investment casting at 2.6764 gr/cm3. The quantity of porosity impacts the density value, according to the results of porosity observations. The phase (Al) and the phase (Zr) are observed in the microstructure results (Si). In gravity investment casting, the beta phase granules (Si) appear to be larger and fewer. The beta phase granules seem smaller and more abundant in gravity die casting. The hardness value is influenced by the size, number, and dispersion of beta granules. Hardness testing with gravity investment casting yielded a hardness value of 86.84 HVN, according to the results.

1 January 2024 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
MAMasyrukan
Masyrukan
IMIrwan Mawarda
Irwan Mawarda
SWSunardi Wiyono
Sunardi Wiyono
BSBibit Sugito
Bibit Sugito
UKUmmi Kultsum
Ummi Kultsum
NINur Annisa Istiqamah
Nur Annisa Istiqamah
The purpose of this research is to determine the effect of casting mold inlet (In-Gate) diameter on chemical composition, porosity defects, micro-photographs, and casting product hardness. The casting sample material is made from scrap aluminum and poured into the mold in 5mm, 7.5mm, and 10mm In-Gate diameter variations. Chemical composition testing, porosity observation, microphotography with a metallography microscope, and Brinell hardness testing (ASTM E– 10 standard) are used to collect data for this investigation. The result indicates that the sample aluminum alloy silicon metal (Al-Si) material has an 81.86 percent aluminum content and a 9.84 percent silicon content. The 10mm In-Gate size has the highest hardness value of 98.68 BHN, while the 7.5mm In-Gate has a hardness value of 84.46 BHN. Due to porosity defects that can reduce metal hardness, the 5mm In-Gate has the lowest hardness value of 73.07 BHN.