Metal is an essential substance in the industrial world for supporting human life and technological advancement. Shaping and increasing metal’s ability involves the heat treatment process. This research aims to see how the microstructure and hardness of metal change after being heat treated with quenching and tempering medium at room temperature and ice. The experiment was conducted utilizing a heat treatment process involving heating the material to 840°C for 60 minutes, then quenching it with water and ice and tempering it at 200°C for 20 minutes. The hardness test employs the Rockwell Hardness Test method, which uses a 9-point hardness scale with the primary load (P) of 150kg-f. The observations for the micro test were in the form of density variations in ferrite, pearlite, and martensite crystal grains. Microstructure investigations showed the presence of martensite in the material after being heat-treated. The hardness test showed that the carbon steel material experienced a decrease in hardness from the initial value of 43.12 HRC to 39.32 HRC and 38.14 HRC after quenching water and ice water. The comparison of tempering has no significant effect on hardness with values of 40.63 HRC and 38.94 HRC tempering followed by water-quenching and ice water-quenching, respectively.
The purpose of this research was to investigate the performance of photovoltaic modules when used in different heating temperatures. The heating temperature variants used were room T, TA = 50 °C, TB = 60 °C, and TC = 70 °C. The lamp capacity used was 5 watts with a bulb-type lamp. In addition, the circuit used was a series circuit. This research done on the effect of different temperatures of the heater placed under the photovoltaics showed that when there was an increase in the photovoltaic temperature, the voltage, current, power, and efficiency decreased. Therefore, it is necessary to limit the temperature used for photovoltaics.
The purpose of this research is to determine the effect of casting mold inlet (In-Gate) diameter on chemical composition, porosity defects, micro-photographs, and casting product hardness. The casting sample material is made from scrap aluminum and poured into the mold in 5mm, 7.5mm, and 10mm In-Gate diameter variations. Chemical composition testing, porosity observation, microphotography with a metallography microscope, and Brinell hardness testing (ASTM E– 10 standard) are used to collect data for this investigation. The result indicates that the sample aluminum alloy silicon metal (Al-Si) material has an 81.86 percent aluminum content and a 9.84 percent silicon content. The 10mm In-Gate size has the highest hardness value of 98.68 BHN, while the 7.5mm In-Gate has a hardness value of 84.46 BHN. Due to porosity defects that can reduce metal hardness, the 5mm In-Gate has the lowest hardness value of 73.07 BHN.
Welding techniques have historically been commonly employed in machine construction for repairs, hardening tool coatings, thickening worn sections, and connecti
The annealing process is widely used to remove residual stresses in the production process so that steel becomes more ductile. This study aims to investigate the effect of variations in temperature and holding time on the hardness and microstructure of ST 60 steel in the annealing process. This study uses temperatures (750°C), (800°C), (850°C) and (900°C), and the time parameters of the annealing process are 15 minutes, 30 minutes, 45 minutes, 60 minutes. The results of this study indicate that at a temperature of 750°C and holding times of 15 minutes, 30 minutes, 45 minutes, and 60 minutes. The hardness value has an average of 62 HRA. At a temperature of 800°C with holding times of 15 minutes, 30 minutes, 45 minutes, and 60 minutes the average hardness value is 59.67 HRA. Then at a temperature of 850°C with a holding time of 15 minutes, 30 minutes, 45 minutes, 60 minutes the average hardness value is 53.67 HRA and at a temperature of 900°C with a temperature of 15 minutes, 30 minutes, 45 minutes, 60 minutes is 53 HRA. The raw material has an average hardness value of 66.7 HRA. When the raw material after undergoing the annealing process decreased. This shows that the higher the temperature and holding time in the annealing process, the higher the hardness of the material.
Penguatan pembelajaran berbasis CAD (Computer Aided Design) di SMK Muhammadiyah 2 Semarang merupakan langkah strategis dalam menyiapkan lulusan SMK yang kompetitif di dunia industri, terutama teknik mesin. Program pengabdian masyarakat ini bertujuan untuk meningkatkan pemahaman guru terhadap penggunaan perangkat lunak CAD, meningkatkan keterampilan dalam metode pengajaran berbasis teknologi, serta mengembangkan modul pembelajaran interaktif. Kegiatan ini meliputi pelatihan, pendampingan, dan evaluasi berbasis tugas mandiri. Hasil pelatihan menunjukkan peningkatan dalam keterampilan guru menggunakan perangkat CAD. Program ini diharapkan dapat menjadi model pembelajaran CAD bagi siswa di SMK Muhammadiyah 2 Semarang oleh guru yang sudah mengikuti pelatihan.