Heterogeneous integration of III–V active devices on lithium niobate-on-insulator (LNOI) photonic circuits enable fully integrated transceivers. Here we present the co-integration of InP-based light-emitting diodes (LEDs) and photodetectors on an LNOI photonics platform. Both devices are realized based on the same III–V epitaxial layers stack adhesively bonded on an LNOI waveguide circuit. The light is evanescently coupled between the LNOI and III–V waveguide via a multiple-section adiabatic taper. The waveguide-coupled LEDs have a 3-dB bandwidth of 40 nm. The photodetector features a responsivity of 0.38 A/W in the 1550-nm wavelength range and a dark current of 9 nA at −0.5 V at room temperature.
Grating couplers are developed as one of building blocks in silicon photonics to couple light between on-chip devices and optical fibers. For emerging high-capacity datacom and telecom systems enabled by space division multiplexing, it is essential to couple light together with mode conversion functions. In this work, we show the feasibility of combining conventional grating couplers and mode converters, both with a high efficiency. The proposed devices are very compact, built on standard Silicon-on-Insulator wafers, with no extra fabrication efforts required. It is shown that the LP01, LP11a, LP11b and LP21b modes in a few-mode optical fiber can be successfully excited directly from the proposed grating couplers, which have the fundamental mode as an input from an integrated waveguide. The overall coupling efficiency, including mode conversion efficiency, can be as high as 50%. We also analyze the performance of the grating couplers in terms of bandwidth, efficiency and tolerance to device fabrication errors.
Erbium-doped waveguide amplifiers are important for silicon photonic large-scale integration. They boost the optical signal to compensate for the on-chip loss of the whole system, such as insertion, transmission, and coupling loss. Herein, a GaAs-on-silicon-pumped erbium-based waveguide amplifier is proposed. The optical amplifier is based on waveguides evanescently coupled with an erbium-doped thin-film gain medium. The erbium-doped gain region is locally pumped by a hybrid GaAs-SiN/SiO vertical-cavity-emitting pump laser. It can be selectively fabricated on the silicon photonic chip that has good position flexibility when integrated with other devices. The amplifier provides high-quality electrically driven amplification and realizes the full integration of amplifiers with the silicon photonic system without any external pump light source. The modeling analyses show that the proposed amplifier design has a maximum saturated gain of 42.5 dB/cm with a modulation bandwidth of ∼42 GHz. This high-gain, large-bandwidth device fully utilizes the advantages of erbium-doped materials and silicon-based III-V semiconductors, while overcoming their issues, and opens up a new pathway for on-chip amplification.
17 August 2020 in Semiconductor Science and Technology
Low threading dislocation density (TDD) in GaAs epitaxial layers grown on silicon substrate (e.g. TDD < 10 6 cm −2 ) is critical for GaAs-based optoelectronic and high-performance electronic devices on silicon. Ge buffers and In x Ga 1-x As/GaAs superlattice layers (SLs) are commonly used to reduce the TDD in GaAs epitaxial layers grown on Si wafers. In previous reports, TDD of ~10 7 cm −2 in GaAs and InGaP layers grown on 200 mm Si wafers was achieved by using Ge buffers only (e.g. Wang et al 2017 Semicond. Sci. Technol.32 125013) and TDD of ~10 6 cm −2 in GaAs epi-layers for quantum dot lasers on Si was achieved by using SL insertion layers (e.g. Shang et al 2019 IEEE J. Sel. Top. Quantum Electron.25 1502207). In this work, the effectiveness of the dislocation filtering effect of In x Ga 1-x As/GaAs SLs combined with Ge buffers is investigated. The results are compared with wafers where In x Ga 1-x As/GaAs SLs were directly grown on GaAs-on-Si buffers without Ge buffers. The In x Ga 1-x As/GaAs dislocation filter layers (DFLs) consisted of 10 nm In x Ga 1-x As/10 nm GaAs layers superlattice spaced by GaAs layer. Then, 1000 nm thick InGaP layers were grown on top of the DFLs to characterize the effect. Transmission electron microscopy, etch-pit density, x-ray diffraction, and photoluminescence were performed to characterize the quality of the materials. Our results indicate that for the growth with Ge buffers there was no significant difference in the final TDDs in the InGaP layers compared with a reference wafer that did not have DFL. For the growth without Ge buffers, the dislocation filtering effect was indeed observed, although it was not as significant as in other reports. For all wafers with DFLs, large wafer bow and dense film cracks appeared, which hinders the practical application of this method.
In this study, we present a chiral metasurface structure based on graphene-Au elliptical hole arrays. Circular dichroism of up to 0.91 is achieved by varying the rotation angle of the elliptical hole. Circular dichroism (CD) typically expresses the chiral response. The structure has excellent absorption of right circularly polarized light while reflecting left circularly polarized light, and it is theoretically analyzed using the Jones matrix. By incorporating graphene between the gold hole array and the dielectric, the CD can be finely tuned. The CD response decreases from 0.88 to 0.55 when the Fermi energy level of graphene is changed from 0.3 eV to 1.0 eV, as indicated by computational studies. In addition, the periodic cell structure based on this metasurface can realize the digital imaging function and the dynamic modulation of the imaging state can be achieved by adjusting the Fermi energy level, which has potential applications in fields like communication encryption.